您要查找的是不是：
- piston rod cotter 活塞杆栓,活塞杆制销
- Worn crankcase piston rod seals O-rings on. 曲轴箱柱塞连杆O型圈磨损或柱塞衬套磨损。
- Worn crankcase piston rod seals. 曲轴箱连杆密封件损坏。
- Replace crankcase piston rod seals. Replace O-rings. 更换新的曲轴箱柱塞连杆O型圈。
- When assembling, leave the mark on body of piston rod frontward. 装配时，杆身上的记号要朝前。
- Th e piston rod should befitted with the crosshead arenow going tryit. 活塞杆应与十字头孔配合。
- A beam that connects the piston rod to the connecting rod of a reciprocating engine. 十字头连接活塞杆和往复式发动机连杆的横杆
- As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted. 当活塞下行时，棘轮连接活塞杆和发动机轴，因此将功率输送出去。
- THE SEALING BETWEEN THE CRANKCASE AND SCAVENGING AIR BOXES IS ACHIEVED BY MEANS OF PISTON ROD STUFFING BOXES. 曲柄箱与扫气箱之间的密封是通过活塞杆填料函实现的。
- A hydraulic lock is installed on the vertical leg cylinder to avoid extending of the leg piston rod in operation. 在支腿垂直油缸上装有液压锁,能可靠地防止行驶时支腿活塞杆伸出。
- External diameter E and piston rod diameter D will not comply with the above standard due to different applications. 根据用途，缸体外径E，活塞杆直径d有时与上述尺寸不同。
- Gas piston rod and receiver. Note the recess on the bottom of the receiver, it is for the bolt locking. 导杆及枪匣，注意枪匣内下方的凹槽，供枪机闭锁用。
- An oscillating lever connected to an engine piston rod and used to transmit power to the crankshaft. 传动杆可摆动的杠杆，与引擎之活塞相连，用以向机轴传送能量
- In all designs, the valve stem normally serves as a piston rod with disc fastened directly to them. 在所有结构中，阀杆通常作为活塞杆，阀瓣直接固定在阀杆上。
- The AFO cylinder features include a stainless steel tube and roller burnished piston rod. 气缸的踝足矫形器功能还包括一个不锈钢管，辊磨光活塞杆。
- The piston rod of family sedan's rear snubber fractured duringearlier stage of rotary bending fatigue test. 家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
- Hard-chromed piston rod with micro-grooves, increasing the rigidity and reducing friction, keep better lubrication action. 活塞杆微裂纹镀硬铬,增因硬度减少磨擦,保持油膜润滑效果值。
- Abstract： The piston rod of family sedan’s rear snubber fractured during earlier stage of rotary bending fatigue test. 摘 要： 家轿后减振器活塞杆在进行旋转弯曲疲劳试验时出现早期断裂。
- This paper introduces the problems of disc type deburrer installation debugging and made a depth piston rod steering structure analysis. 针对圆盘式去毛刺机在安装调试中出现的问题,分析了其活塞杆导向结构,提出了解决方案,最终得到满意的结果。
- The fracture of piston rod of new hydrogen compression pump is studied by metallography and electron probe in this paper. 用金相显微镜和电子探针对新氢压缩机活塞杆断口进行了分析。
