您要查找的是不是：
- You'd better make it in a shape of cylinder. 你最好把它做成圆柱形。
- Blunt wire points of cylinder or flats. 锡林或盖板针布尖端变钝。
- Poor condition of cylinder under casing. 罩盖下的锡林状态不好。
- The cheese was formed into the shape of cylinder. 乳酪被做成圆柱状。
- piston of cylinder 柱状活塞
- Changing the rate of cylinder rotation changes the speed selected. 改变圆筒旋转速率就改变被筛选的速率。
- A spring holds the other ends in contact with the piston of a hydraulic cylinder. 另一端由一个弹簧托住，与液压缸的活塞相接。
- The plunger or piston of a force pump or hydraulic press. 活塞压力泵或水压机内的柱塞或活塞
- Augmenting the initial displacement of piston of lift cylinder reduces the velocity and acceleration of the platform of hydraulic static pile diver. 增大升降油缸活塞的初始高度，能减小压桩机加力压桩时的机身速度和加速度；
- According to a lot of experiments, the flow of the engine oil in the piston of the air cylinder relates close to single-phase air flow. 根据长期试验研究了解到,汽缸活塞环内润滑油的流动与单相空气流动问题有很大的关联,气流涡动位置预示着油粒位置。
- Reciprocating pumps convert rotary motion to linear motion. Pump speed in rpm determines the pumps output volume for any given combination of cylinder bore and piston stroke. 循环泵将曲轴旋转运动转化为柱塞的直线运动。泵速转每分钟决定了任何气缸和活塞组合的排泵量。
- The chamber in which a piston of a reciprocating engine moves. 汽缸有往复式发动机的活塞移动的空室。
- Hot load and mechanical load coupling make piston to produce crackle, piston-ring glued and scuffing of cylinder bore and so on. 热负荷和机械负荷耦合将导致活塞产生裂纹、活塞环胶结以及拉缸等。
- What should be paid attention to in the overhaul of cylinder? 在气缸大修过程中应该注意什么?
- Reducing the initial displacement of piston of lift cylinder, or augmenting the piston diameter of lift cylinder, will reduce the displacement of the platform of hydraulic static pile driver. 降低压桩机升降油缸活塞的初始高度，或增大压桩机升降油缸活塞直径，均能减小压桩机加力压桩时压桩机的机身位移。
- We are importer of cylinder head, pls contact with us. 我们求购汽车汽缸盖，请与我们联系。
- Improper handling of cylinders can injure your hands, back or feet. 不当操作气瓶能损伤手、背、脚。
- If any other requirements for piston rod head, U type ring width of cylinder lid, and diameter of pin are needed when placing an order, it is recommended to use our existing forged pieces. 订货的场合，如果对活塞杆头、油缸盖的U形环的宽度、销子的直径等尺寸方面另有要求时，建议采用能够利用的本公司现有的模锻件。
- Measurement of vertical concetricity between crosshead and piston of compressors. 压缩机活塞与十字头垂直同心度的检测和调整。
- Last impacting velocity of the piston of pneumatic DHT hammer contacts nearly capability of pneumatic DHT hammer. 风动冲击器活塞的冲击末速度决定了冲击器的工作性能。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
