您要查找的是不是:
- Temperature Field Destroy Analysis of Notch- lay- thermocouple Method for Measuring Round Pipe Wall Temperature 开槽敷设热电偶测圆管壁温对温度场的破坏分析
- The target is mounted on a support passing through the pipe wall. 标板装在穿过管壁的支撑上。
- Tells FDS to record the wall temperature of all solid surfaces. &BNDF QUANTITY='WALL_TEMPERATURE' / 告诉FDS 记录全部固体表面的墙温度。
- The result indicates that the supersaturation caused by the temperature grades between main flow and the pipe wall is the inherent impetus of salt-out in green liquid. 结果表明,因主流与管壁间的温度梯度而产生的过饱和度是绿液发生结盐的内在推动力;
- Stainless steel single and double wall temperature control containers. 不锈钢容器及带温控夹套砂磨筒。
- Rifled or other pipe wall corrugation may change the flow from a hetero-generous to a homogeneous regime by introducing a secondary circulation. 在有来复线的或其它的管壁皱纹的管中,由于引起副流,可能将非均质流转变为均质流。
- The infrared radiation and wall temperature were obviously decreased by cooling. 通过冷却,各喷管的壁温和红外辐射强度明显降低。
- The reduction of noise lever measured in the acceleration on the pipe wall is obtained about 6 to 10 decibel. 结果表明,对于泵的额定工况,所采用的方法可达到管壁振动加速度降低6-10分贝。
- The amplitude of wall temperature fluctuation is larger than that of fluid temperature oscillation. 流量的波动又引起了管壁温度和流体温度的周期性波动;
- The calibration method of pipe wall coefficient of chlorine modelfor large-scaled WDS is studed. 2)对供水管网管壁反应系数进行校核研究。
- From the curves of wall temperature vs axial length , the location of dryout points were obtained. 由壁温随长度的变化曲线得到干涸点产生的位置。
- To extend its life cycle we can also paint DPC spraying anti-corrosion coatings in the dill pipe wall. 也可根据用户要求,在整体加重钻杆内壁喷涂DPC防腐涂料,延长其使用周期。
- The wall temperature,collapsed liquid level and liquid carryover transient are measured. 试验表明,再淹没过程中,定位格架下游的元件表面温度明显下降,骤冷前,定位格架下游的传热系数比上游高,特定工况下,可高出70%25,定位格架对传热的影响程度随试验参数及距骤冷前沿位置的不同而不同;
- Selection of the thin steel pipe. Usually railing pipe wall thickness is about 1.8 mm, these products only 1.1 mm. FYI. 现在的梦想决定着你的将来;所以还是再睡一会吧.
- The wall temperature distribution is tested on an annular combustor by using thermocouple and temperature-indicating paint. 壁温分布试验在全环形燃烧室试验台上进行,采用热电偶和示温漆测量。
- Pipe wall smooth formation, no bubbles, nicks and obvious scar patterns Depression, color and uneven discoloration decomposition line. 管材外壁光滑、平整、无气泡、裂口和明显痕纹凹陷、色泽不均及分解变色线。
- The heat losses and wall temperature under steady heat conduction of Fiber linings in enamelling furnace are calculated and analysed. 分析计算了在稳态导热情况下搪烧炉纤维炉衬不同结构时的散热量和外壁温度,给出了炉衬经济厚度的计算公式和计算方法。
- Cleaning of the volume pipe shall be made before recalibration to remove greases in the standard section of the pipe and wax deposited in pipe wall. 在复检前需要对体积管进行清洗,去除体积管标准段内的油垢和管壁上的结蜡,如果清洗不彻底,将直接影响体积管的标准体积及准确度。
- The wall temperature distributionin different impinging jet heigtht are given,as well as sensitivity and accuracy of the technology arediscussed. 文中给出了在不同射流高度下壁面温度分布的等值线,并讨论了液晶测温技术的灵敏度及测试精度。
- The wall temperature of combustion section for an afterburner is significantly related to the safety of an aircraft and aeroengine. 加力燃烧室燃烧段的壁温对飞机和发动机的安全关系重大,单靠数值计算是很不够的,目前主要靠测试取得。