您要查找的是不是：
- Concrete Pumping to Higher Place and Pipe Line Layout for Chongqing Egongyan Bridge 混凝土高程泵送及管线布设
- Succinct line layout abandons excessive garishness. 简洁而洗练的一字造型摒弃过多的花哨，把一切都交由门板去演绎。
- Propose and validate assembly line layout. 提案以及验证组装线布置.
- Does your line layout prevent them for helping each other? Whether? 你的产品线规划是否令不同的产品线之间无法相互协助?
- Debris in pipe line is too fine to be trapped by strainer. 管线内的碎片太细小导致过滤器无法截留。
- DWTT separation fracture has been analyzed for pipe line steel. 摘要文章对管线钢DWTT试样上出现的分离断口进行了分析。
- Maximum continuous flow based on pipe line velocity of 20 ft. per second. 最大持续流量以管路流速每秒20英尺为计算基础。
- Prior to installation, thoroughly flush pipe line to remove any foreign matter. 在安装之前,彻底冲洗管线,清除任何外来物质。
- Establish line layout that maximizes workflow and spatial utilization while ensuring production efficiency and workplace safety. 建立生产线并在确保生产效率以及车间安全的前提下最大程度上规划产线流程和空间利用。
- Technical and Economic Analysis on Design of Production Pipe Line of C.P.P. 选煤厂生产管道设计的技术经济分析。
- Maximum intermittent flow based on pipe line velocity of 25 ft. per second. 最大间歇流量以管路流速每秒25英尺为计算基础。
- Clear pipe line with pressurized steam before installation steam trap. 安装疏水阀之前应用带压蒸汽吹扫管道。
- Work with product engineers to develop and document assembly and test procedures, line layout, and identify and purchase capital equipment as required to reach volume production release. 按要求与产品工程师合作促进文件汇编、实验程序、生产线规划,以及确定并购买主要的设备来达到生产量。
- Swing Check valves prevent reversal of flow through pipe lines. 旋启式止回阀可以防止管路中的流体倒流。
- The DC-RF performances for the RF MOSFETs with microstrip line layout were improved by applying tensile strain on plastic and also confirmed by T-Supreme and Medici simulations (TMA). 除此之外，由于塑胶基版是可弯曲的，因此可以将伸展的应力应用于其上，此种应力将可以改善矽射频金氧半场效电晶体的直流及射频效能，同时我们也利用模拟软体的方式来验证之。
- Protective gas system: pipe line from the protective gas generation station to reducing annealing furnace. 保护气系统:从保护气体发生站至还原退火炉的管道。
- After installation of valve, support the pipe line; a sagging pipe line can distort the valve and cause failure. 在安装阀门后，要对管道加上支撑物，否则下垂的管道可能会使得阀门变形并造成故障。
- After installation of valve, support line; a sagging pipe line can distort valve and cause failure. 安装阀门后，要支撑住管道：下垂的管道会使阀门产生变形而导致失败。
- Prior to installation, flush the pipe lines to remove foreign material. 在安装之前,要冲洗管线,清除外来物质。
- The flared fitting is a connector in order the pipe line system, in which oil, water, gas and all kinds of corrosive materials are used as the medium. 扩口式管接头是以油、水、气和各种腐蚀性材料为介质的管路系统中的一种连接件。
