您要查找的是不是：
- Eradicates yeast, fungus and mold. 消除微菌，霉菌等。
- phenolic and molding 树脂砂造型
- Tailor's Ham: used for pressing and molding curved areas. 烫凳:用于熨烫和塑造弯曲部位。
- This gives it a very competitive edge over most bacteria and mold. 这是一个很大部分细菌和霉菌竞争。
- Limit your outside activities if you are bothered by ragweed and mold. 当你受豚草和霉菌困扰时，尽量限制户外活动。
- Phenols and anilides can be nitrated with very dilute nitric acid. 酚类和酰基苯胺能被极稀的硝酸硝化。
- A new syntan product was prepared with tar phenol and ligninsulfonic acid. 以工业副产物木素磺酸和焦油酚为主要原料研制出一种新的合成鞣剂。
- The Nonylphenol was synthesized with phenol and nonene as the main materials. 以苯酚、壬烯为主要原料合成壬基酚。
- The rice dampened and molded during the summer rains. 在夏天雨季大米已受潮发霉。
- Method:The level of urinary MCH was measured with phenol and 4 AAP assay. 方法：酚，4－氨基氮替比林（4－AAP）法测定尿红细胞平均血红蛋白含量（MCH）。
- The major pollution indicators are dissolved oxygen, potassium permanganate, BOD, volatile phenol and petroleum. 主要污染指标为溶解氧、高锰酸盐指数、生化需氧量、挥发酚和石油类。
- The Saturn V rocket is sprouting plants and mold and its structure is home. 土星V号火箭正繁演各种植物及菌类还有结构体是温床。
- Other causes include organisms such as dust mites and molds. 另外一些引起过敏的原因包括如尘螨和真菌等微生物。
- Describes some results of using rectorite for molding sand and mold coating. 介绍了用累托石粘土作型砂粘结剂和水基涂料悬浮剂的试验结果。
- As antirust paints for ship hull in non-immersed areas, compatible with alkyd, phenolic and chlorinated rubber finish. 主要用于船体水线以上部分的防锈用漆，可与醇酸、酚醛、氯化橡胶面漆配套使用。
- This process is called "osmosis," and it can be deadly for bacteria and mold. 这个过程被称为“渗透”并且可以导致细菌和霉素死亡。
- The major components of acidic fraction are phenols and organic acids. 酸性组分主要由酚类化合物和有机羧酸组成.
- The major pollution indicators are dissolved oxygen,potassium permanganate,BOD,volatile phenol and petroleum. 主要污染指标为溶解氧、高锰酸盐指数、生化需氧量、挥发酚和石油类。
- The influences which caused by the kinds of the catalyzer, phenol and formaldehyde proportion, boracic acid addition and etc were discussed. 探讨催化剂种类、酚醛比、硼酸加入量等对其性能的影响。
- Knowledge of ceramic or plastic injection molding process, equipment and mold design is a must. 必须具备陶瓷或者塑料成型工艺、设备和模具的设计知识。
