您要查找的是不是:
- At present,very little test data is available about the peak shear strength between the grout and the bore wall in the interior bond section of prestressed anchorage cable. 关于锚索内锚固段注浆体与孔壁之间的峰值抗剪强度,目前很少有试验资料可供采用。
- As compared with the compacted specimens, the natural specimens were higher in the peak shear strength and the dilatancy due to the cementation effect of the iron and manganese oxides. 当吸力相同时,原状样的峰值强度和剪胀势均高于压实样,这与原状样中铁锰结核的胶结作用有关。
- TESTING STUDY ON THE PEAK SHEAR STRENGTH BETWEEN GROUT AND BORE WALL IN THE INTERIOR BOND SECTION OF PRESTRESSED ANCHORAGE CABLE 锚索内锚固段注浆体与孔壁之间峰值抗剪强度试验研究
- peak shear strength 最大剪切强度
- Flow-mediated dilatation response normalized to peak shear rate was significantly lower in migraine patients than in controls, the report indicates. 报告指出,流量介导的肱动脉扩张与标准的高峰速度阶差相比,偏头痛病人扩张流量低于对照组。
- The shear displacement for the dilatation is always less than that at the peak shear stress. 剪应力达到峰值所需要剪位移总是比剪胀发生时所需的剪位移大。
- Touch and close fasteners - Determination of longitudinal shear strength. 粘接拉链。纵向剪切强度的测定。
- The results show that the shear strength of COF is higher than that of COG. 结果表明 :COF比 COG的剪切强度高 .
- The shear strength of the composite is improved above to 11 MPa from 5.5MPa. 改性后碳 /聚芳基乙炔复合材料的剪切强度由 5 5MPa提高到 11MPa以上
- The shear strength of COG and COF bonded with ACF is studied by impact test. 摘要采用冲击试验方法研究了各向异性导电胶膜(ACF)互连的玻璃和柔性基板上倒装芯片(COG和COF)的剪切结合强度。
- The adhesive should preferably have a shear strength greater than 30 mpa . 粘结膜最好具有大于30毫帕的剪切强度。
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- Ambitious attempts to improve interlaminar shear strength have been made by Mueller Prosen and by Keogh. 米勒·普罗森还有基奥都对提高层间切变强度作了大胆的尝试。
- Variation Rule of Shear Strength Index When Direct Shear Test of Coarse-grained Soil. 粗粒土直接剪切试验抗剪强度指标变化规律。
- Embedded columns can increase shear strength as well as control of displacement and failure. 配以暗框边柱能提高剪力墙的抗剪强度、位移控制和破坏控制能力。
- The wood is moderately hard and strong with high bending strength, shear strength and stiffness. 这类木材硬度适中而强壮,具有高度弯曲力、剪力和硬度。
- The melting point and the shear strength of Bi-Pb-Sn-Cd fusible alloys were determined by DSC and tension tester. 利用差热分析仪和拉伸试验机;研究了易熔合金Bi-Pb-Sn-Cd的成分对合金熔点和剪切强度的影响.
- Besides, the undrained shear strength was increased slightly due to the negative pore pressure. 不排水条件下由于负孔隙水压力的存在,土样的表观强度略有增大。
- The results showed that the shear strength of epoxy bonded joint decreased after it was aged in acid media. 结果表明,环氧胶接接头在酸性介质中老化后,其剪切强度明显降低;
- The results showed that the shear strength of fractal joints decreases nonlinearly as the filling percentage increased. 结果表明,随着充填度的增大,分形节理抗剪强度总体上呈非线性减小。