您要查找的是不是：
- The bore and outside diameter tolerances of SKF single and double direction tapered roller thrust bearings are produced, with very few exceptions, with Normal tolerances to ISO 199-1979. SKF单向和双向圆锥滚子推力轴承的孔径和外径公差除少数例外,均按照ISO 199-1979标准的普通级公差生产。
- Collars-Inside and Outside Diameters Tolerance Selection Type 金属轴环-内外径公差选择型
- The eccentric diameter tolerance which is h9. 偏心直径公差为h9。
- Single plane mean outside diameter deviation. 单一平面平均外径偏差。
- Remark: Consult order for special outside diameter. 注:特殊外径需协议订货。
- Check the outside diameter of stabilizers. 检查扶正器的外径。
- A 3/4" NPT pipe thread has an outside diameter - OD - of 1.050 inches. 例如：一个标准为3/4"NPT的管外部直径为1.;050英寸。
- Grinding wheel outside diameter thickness and bore may be customer specificied. 砂轮外径、厚度、孔径可依客户需求指订尺寸。
- The cam-bores may present a roundness error within the diameter tolerance, so the most significant diameter value for the shim/tappet thickness determination is the one along the valve train axis. 凸轮孔可能会出现直径公差范围内的误差，所以决定垫片/凸子厚度的最大直径值应位于气阀机构的轴部。
- In the past, Thinnet coaxial cable with an outside diameter of only 0.35 cm was used in Ethernet networks. 在过去，外围直径仅0.;35公分的细同轴电缆被用在乙太网路。
- The control accuracy of inside &outside diameter is very high,suitable for various splices. 内外径尺寸精度控制高，适合各种接头。
- Subsequently, the effective area was demarcated manually, and rolling bearing outside diameter character was distilled. 接着采用区域人工标定，进行滚动轴承外径的特征提取。
- To make sure that the bearings are correctly mounted, a "V" is marked across the outside diameter of the bearing pair (fig 8d). 为了确保轴承的正确安装,在配对轴承的外径上标有“V”(图8d)。
- The shank diameter tolerance which is h7, and, 芯柱体直径公差为h7
- In my setup I used aquarium air pump tubing (6 mm outside diameter) for the manometer (pressure gauge) although it results in a small capillary error. 在我制作的装置中,使用鱼缸的空气泵管路(外径6 mm)作为压力表(压力计),尽管它会导致小的毛细管误差。
- Diameter tolerance of steel wire 钢丝直径
- Mini Rods-Outer Diameter Tolerance Fixed Type 小口径棒材-外径公差选择型
- The outside diameter of copper tube shall be tested by Micrometer. The tooth depth and the bottom wall thickness shall be tested by Microscope. 外径尺寸用外径千分尺测量.;齿高和底壁厚用双目倒置小金相测量。
- Description: Type GC-A is a roller type freewheel non-bearing supported.Nominal outside diameter is a standard ball bearing dimension. 系列为无轴承支撑滚柱式单向离合器，外部尺寸与标准轴承尺寸相同。
- LH-PL series of spray cooling box mainly used for supplementary cooling pipes to ensure the accuracy of pipe outside diameter size. PL系列喷淋冷却箱主要用于管材的补充冷却以确保管材外径尺寸的准确性。
