您要查找的是不是：
- outer rings quenching press 外圈淬火压床
- Coning Deformation Analysis in Bearing Outer Ring Quenching 轴承外圈淬火锥度变形分析
- One intermediate ring between the two outer rings. 两个外圈之间带一个隔圈。
- The outer ring contains the valence electrons. 排在外层的有价电子。
- Deviation of a single width of the outer ring. 外圈单一宽度偏差。
- Outer ring with integral central flange and two loose flange rings. 外圈带整体式中心法兰和两个松配合法兰圈。
- One integral flange on the outer ring and one loose flange ring. 外圈带一个整体式法兰和一个松配合法兰圈。
- Stay on the outer ring road and follow the signs for Sandown. 所有的2岁以下的儿童在使用现有的床铺之下不需付费。
- Consisting of outer ring, inner ring, double-row steel balls and cage. 由外圈,内圈,两列钢球及保持架构成。
- They can also be supplied as self-retaining units with a retention sleeve over the outer rings (fig 10). 它们也可以作为自保持式单元供应,外圈上有保持套筒(图10)。
- Next we linked the ligands to form a big outer ring called a macrocycle. 接下来我们又把几个配位基连接起来，做成一个大型的外环结构，称为巨环。
- Where misalignment between the inner and outer rings exceeds 1 minute of arc, the action of the load on the flange changes considerably. 内圈和外圈之间的不对中超过1分弧时,作用在法兰上的载荷会发生相当大的变化。
- GSG uses Gleason quenching presses to make sure the heat distortion of gear under control. GSG使用格里森多台淬火压床;使产品的热变形量被控制在最小的范围内.
- Self-retaining bearing units with large contact angle, outer rings held in a retention sleeve, pierced rollers and steel pin-type cages (fig 10). 带有大接触角度、夹在保持套筒里的外圈、穿孔滚子和钢支柱式保持架的自保持式轴承组件(图10)。
- quenching press oil temperature control 淬火压床油温控制
- The inner rings with roller and cage assembly and outer rings of SKF tapered roller bearings having the same designation are interchangeable. SKF圆锥滚子轴承中型号相同的带滚子和保持架组件的内圈和外圈可互换。
- Full complement cylindrical roller bearings with flanges on both inner and outer rings can support axial loads in one direction. 内圈和外圈都带法兰的满滚子圆柱滚子轴承可支撑一个方向上的轴向载荷。
- The main SKF focus is on the bearings without intermediate rings which have four outer rings and, of course, on the sealed bearings. SKF的主要重点放在不带中间圈但有四个外圈的轴承上,当然也放在密封轴承上。
- The main difference is the configuration, or arrangement, of the roller and cage assemblies and the number of inner and outer rings dictated by this. 主要区别是滚子和保持架组件的结构或配置以及规定的内圈和外圈数量。
- There were 4 suckers in C.pisiformis and the scolex of T.pisiformis,and 37 hooks in the rostellum arranging with inner and outer rings. 结果表明，豆状囊尾蚴和豆状带绦虫均有4个吸盘，37个小钩分内、外两圈排列在顶突上。
