您要查找的是不是:
- optimize welding line 优化焊缝
- THE EQUIPMENTS AND FIXTURE OF WELDING LINE. 焊装线设备及工装夹具
- Introduced planar welding line detect sensor based on GMR. 简述了基于GMR的二维焊缝检测传感器。
- Liu Chuntai,Shen Changyu.Using TAGUCHI methods to optimize the weld line strength in injection molded short-fiberreinforced PA66[J].Acta Materiae Compositae Sinica,2004,21(5):68-73. [4]刘春太;申长雨.;利用TAGUCHI方法优化纤维增强PA66注塑熔接线拉伸性能[J]
- A three-dimensional welding line detect sensor based on GMR was introduced. 简述了基于GMR的三维焊缝检测传感器。
- Weld Area Crack. A crack in or immediately adjacent to the weld line. 焊缝区裂纹。在焊缝线或紧靠焊缝线出现的裂纹。
- Do not make a round trip jolty porch rail, lest the welding line of baluster bottom ruptures. 不要往返摇动阳台栏杆,以免栏杆底部的焊缝断裂。
- With Cold Jet, complete weld lines can be cleaned in 25 minutes. 如果使用Cold Jet,彻底清洁焊缝可在25分钟之内完成。
- Variations in the properties of the weld occurring at short regular intervals along the weld line due to repetitive variation in welding heat. 由于焊接热量周期变化,使得沿焊缝线每一固定的小间距焊缝的性能出现周期性变化。
- Utilized this method to segmentalize the image of oil derrick arc welding robot welding line gets up the good effect. 将该方法运用于石油井架弧焊机器人焊缝图象的识别中起到很好的效果。
- The maximum value of gapwise-averaged birefringence along the weld line occurred at a small distance from the obstacle. 制品最大双折射值出现在嵌件后一定距离处。
- Study on the properties of welding line near line section aluminium lithium alloy 1420 by Russia scholar is introduced. 主要介绍了俄罗斯学者关于铝锂合金1420焊缝近缝区性能的研究点滴。
- In the experiments of this research, GTAW butts thin plates of stainless steel and forms a weld line. 摘要本研究以不锈钢薄板在惰性气体钨棒电弧焊对接焊方式进行研究。
- Pinhole. A short unwelded area in the weld line extending through the entire pipe so that fluid will leak out through the area very slowly. 针孔。指焊缝线上位焊接的、贯穿管子整个壁厚的细孔,可导致流体从该孔缓慢漏出。
- By changing the structure of welding line and assessing minutia, the fatigue intension of framework welding line will be increased. 通过改变焊缝结构,使焊缝的评定细节发生变化,从而提高机架焊缝的疲劳强度。
- It shows that industrial pure Cu has good weldability, optimized welding parameters can make a joint more strength than the base-material. 研究表明:工业纯铜具有良好的搅拌摩擦焊接性能,优化工艺可获得超强于母材的搅拌摩擦焊接接头。
- All these can be well used for reference to study the cause of molding defects (e. g. warpage, weld line) of ultra-thin wall plastic parts thoroughly. 该结论为深入开展超薄塑件成型缺陷(如翘曲、熔接痕)的形成机理研究提供了有益的借鉴。
- A study concerning the feasibility of equipment for producing the inner ribbed spiral tubes with the existing pipe welding line is given. 分析了在现有焊管机组上生产内凸筋螺旋焊管的设备可行性。
- Laser welding machine and processing for double mass flywheel in automobile enine are studied,and the optimal welding technological parameters are obtained . 对汽车发动机双质量飞轮激光焊接机及其工艺进行了研究,取得了最佳焊接工艺参数,讨论并分析了各工艺参数及其它因素对激光焊接质量、性能的影响。
- Regardless of torch orientation or part size or shape, the EA1400N robot prevents bent, pinched or stretched cables, minimizing wire feed problems and optimizing weld performance. 无论是在焊丝方位或部分大小或形状大小的问题上,为使电线尽量减少供给问题和优化焊接性能。EA1400N机器人都会防止弯曲,挤压或拉伸电缆,