您要查找的是不是：
- NCL: No control limit is allowed. 不允许超出控制界限。
- NCL:No control limit is allowed. 不允许超出控制界限.
- Optimal control for nonlinear plants. 非线性对象优化控制。
- NCL：No control limit is allowed. 不允许超出控制界限。
- The obtained optimal control law consists of analytical linear feedforward and feedback terms and a nonlinear compensation term which is the limit of the adjoint vector sequence. 得到的最优控制律由解析的线性前馈-反馈项和伴随向量序列极限形式的非线性补偿项组成。
- The optimal control law consists of an accurate linear feedback term and a nonlinear delay compensation term that is the limit of an adjoint vector sequence. 最优控制律由精确的线性反馈项和非线性时滞补偿序列的极限项组成。
- It supplies condition for coke oven heating combustion optimal control. 为实现焦炉加热优化控制提供了前提条件。
- By solving iterative the sequences, the optimal control law is obtained which consists of analytical linear feed-forward-feedback terms and a nonlinear compensation term, which is the limit of the adjoint vector sequence. 通过迭代序列得到的最优抚动抑制控制律由解析的线性前馈－反馈项和序列极限形式的非线性补偿项组成。
- Variation beyond a control limit is evidence that assignable causes are affecting the process. 管制界线是从制程的资料来计算，不要和规格界线混淆。
- The new model will be helpful to the further simulation and on-line optimal control for the ASU of the IGCC plant. 这为进一步实现IGCC电站空分系统的动、静态建模，以及计算机在线控制奠定了良好的基础。
- Frequency control limits the number of stations you can tune into. 频率控制限制了你们能调谐进的台站数量。
- A control chart usually displays a lower control limit (LCL) and an upper control limit (UCL). 注 : 一般而言 , UCL与 LCL 的位置为平均值的正负三个标准差。
- This includes computing and interpreting capability indices, estimating the% failures, control limit calculations, etc. 包括计算和解释过程能力指数、计故障百分率、制限计算等。
- The existence and stability of the optimal control is established based on the parabolic regularization method and the weak convergence technique. 用抛物正则化方法和弱收敛技巧，证明了最优控制的存在性和稳定性。
- This paper addresses problems in linear quadratic optimal control of EHT transmission line. 本文论证了超高压输电线路线性二次优化控制的若干问题。
- The optimal control problem is considered for bilinear systems affected by external persistent disturbances. 摘要研究具有外界持续扰动作用下双线性系统的最优控制问题。
- This includes computing and interpreting capability indices, estimating the % failures, control limit calculations, etc. 包括计算和解释过程能力指数、估计故障百分率、控制限计算等。
- The paper uses the optimal control theory to study the effect of the tax rate differences on the dividend policy. 本论文将运用最优控制理论研究税收差异这一因素对公司股利政策的影响,以期从数学模型的角度来得到一些比较严谨的结果。
- A new method of applying a nonlinear optimal control to Static Synchronous Series Compensator (SSSC) is proposed. 提出了一种运用非线性最优控制理论设计SSSC控制器的方法。
- There is no industry control limits for Copper and Lead in SnAgCu solder pot. 目前行业中没有用于SnAgCu焊料槽中铜和铅的控制极限。
