您要查找的是不是：
- oil pan filler cap 油盘加油口盖
- oil pan filler block 油盘油封座
- Please taken the engine oil tank filler caps. 请检发动机滑油加油口盖盖紧。
- Trim or remove excess sealant film in the rear main cap oil pan gasket groovDO NOT remove the sealant inside the rear main cap slots. 修整或清除后主盖机油底壳垫圈凹槽中过多的密封剂薄膜。切勿清除在后主盖槽中的密封剂。
- These include the wider rear bumper and misaligned fuel filler cap. 这些措施包括更广泛的后保险杠和失调燃料填充帽。
- Fill the oil pan with oil to the specified level. 用油填充油底壳到规定油面。
- The washer reservoir, filler cap, and sensor are each available for service. 清洗器存储箱、填注口盖和感知器都可以维修。
- Loosen oil pan bolts and remove the front bolt at each side. 松动油底壳螺栓，拆下每一面的前螺栓。
- The bottom of the block is covered with an oil pan or oil sump. 缸体的顶部是气缸盖，它组成了燃烧室，缸体底部是油底壳。
- The washer reservoir, filler neck, grommet seal, and filler cap are each available for service. 清洗液体槽，填注口颈，套环密封垫和填注口盖可以各自维修。
- Gasoline vapor also condenses on cold engine parts and drips down into oil pan. 汽油蒸气会凝结在冷的发动机零件上，然后流入油底壳。
- The oil pump in the lubricating system draws oil from the oil pan and sends it to all working parts in the engine. 润滑系统中的机油泵从油底壳抽取油并把油输送到发动机内全部正在工作的部分。
- With it, the structure of the 6105 QA diesel oil pan for lower noise is optimized. 并用此系统进行了6105QA柴油机油底壳的低噪声结构的优化设计。
- And the other two rubber cushion seats 3 on the hinge side B are fixed by using a rubber-based adhesive. Then, oil pan 4 is placed. 再用螺钉2把铰链侧B的2个头部胶垫座3钉好固定，然后把底槽4放上去。
- master cylinder filler cap gasket 主缸加油口盖垫密片
- Fill oil pan 1 with JUKI Machine Oil No. 7 up to HIGH mark A.When the oil level lowers below LOW mark B, refill the oil pan with the specified oil. 请把JUKI Machine Oil No.;1机油倒进油槽1里，一直加到HIGH标记A的位置。油槽的油面降到LOW标记B以下时，请再次补充机油。
- The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft. 油底壳和气缸体的下半部分一同被叫做曲轴箱；他们把曲轴封闭起来。
- At the lower part of emergency generator fuel oil tank there is oil fence, auxiliary engine daily service tank has oil pan. 4应急发电机组燃油柜下面设置围油栏，辅机日用油柜设置油盘。
- Shapes and dimensions of fuel oil filler and filler cap for automobiles 汽车燃料油注入口和盖的形状和尺寸
- Gaskets are also used to seal joints between other parts, such as between the oil pan, manifolds, or water pump and the block. 密封垫也同样用于密封其他部件之间的结合处，例如，油底壳、歧管、水泵与气缸体之间的密封。
