您要查找的是不是:
- INTELLIGENT SCHEDULING ALGORITHM FOR PROBLEMS WITH BATCH AND NON CUTTING TIME 考虑批量和辅助时间等生产工况的智能调度方法
- Method: 38 patients with cataracts were emulsified by using non cut pupillary dilation cystotome or diathermic high freguency capsulorrhexis. 方法:应用非切开瞳孔牵拉扩张法及部分下方瞳孔缘括约肌剪断法原位超声乳化碎核等技术对38例小瞳孔白内障行超声乳化。
- Methods The surgery was performed by using non cut pupil dilation and phacoemulsification on 105 eyes of 101 patients with papillary circular synechia. 方法对101例105眼瞳孔环形黏连患者采取非切开瞳孔牵拉扩张法扩大瞳孔,并施行白内障超声乳化术观察视力、瞳孔、术后并发症。
- Automated case-handling systems at Smith's Dairy cut time to load trucks by 40 percent, improve efficiency. 奶制品厂在采用自动化包装箱搬运系统后,装车时间削减了40%25,生产效率提高。
- Ice-cold watermelon on a steamy summer day really hits the spot. But you'll be best served by keeping it on your countertop until cutting time. 酷热的夏天吃冰冻西瓜当然是好享受.;但最好还是一直存放在桌上;不要冰冻的好
- Direct finishing, not only to save the expensive titanium alloy material, but also reduces tool consumption, shorten the cutting time, thereby reducing the cost! 直接精加工,不但节约了昂贵的钛合金材料,也降低了刀具消耗,缩短了切削时间,从而降低了成本!
- That is to measure changes in physical properties during milk coagulation process for defining the coagulation time and then the optimal cutting time of coagulum. 试验研究结果表明:超声信号的衰减与牛奶在凝固过程中的物理性能变化密切相关。
- In rough cut of NC milling of helicoid, there are many defects when the generic programming means, for example,longer cutting time,inefficient , exigent tools are used. 在螺旋曲面的数控粗加工中,采用一般的编程方法得到的刀具路径在实际应用中存在加工时间长、效率低、对刀具要求高等缺点。
- The influence of air cutting angle and air cutting time to chip breakage is studied quantitatively.The correctness of air cutting theory is verified by the experiments. 定量分析了间断切削过程中的空切角度、空切时间对断屑的影响,并通过试验验证了用空切理论分析断屑的正确性。
- The analysis indicates that tapping torque increases as net cutting time ratio increases,where net cutting time ratio influences the tapping torque more significantly. 结果表明,攻丝扭矩随净切削时间比的增加而增大,且对攻丝扭矩的影响最显著。
- The optimization model of machining process scheme is established to obtain shorter cut time, lower cost or higher surface quality.It is helpful to form successful cases for HSM. 提出了以切削时间短、加工成本低、表面质量高为目标的工艺方案寻优模型,该模型有助于形成成功的加工范例。
- The results showed that the effect of cutting frequency on the yields was very remarkable,but cutting time,especial at autumn,was also very important for remaining forage rates of pasture. 结果表明,刈割频率对产量的影响最大,但刈割时间,尤其是秋季最佳刈割时间对维持草地牧草比例平衡是相当重要的。
- This non sequitur invalidates his argument. 他不根据前提推理因而论证无效。
- Then, amid early signs of recovery, it paused, giving the rate cuts time to work. 之后,出现恢复早期信号时,停止降息,给先前降息措施发挥作用的时间。
- That cut is taking a long time to heal. 那伤口要很长时间才能愈合。
- Rose bushes shoot again after being cut back. 玫瑰丛修剪後还能再长出新枝。
- In order not to be late, she cut across the fields. 为了不迟到,她抄近路穿过田野。
- The growth rate and yield of triticale were decreased with the increase of cutting times. 小黑麦刈割次数的增加会造成生长速率的下降,产量降低。
- Patience is a sine qua non for a good teacher. 做个优秀教师必不可少的条件是要有耐心。
- The diplomat was declared persona non grata. 这位外交家被宣布为不受欢迎的使节。