您要查找的是不是:
- To form(metal) by a mechanical or hydraulic press. 锻制通过机械或水的压力锻制
- A heated hydraulic press was required for adhesion. 为了获得附着力,需要热力水压。
- The plunger or piston of a force pump or hydraulic press. 活塞压力泵或水压机内的柱塞或活塞
- The hydraulic press is the biggest one that we have ever seen . 这台水压机是我们见过的最大的一台。
- This study applies a state feedback based Closed-LoopCombustion Control (CLCC) using Fast ThermalManagement (FTM) on a multi cylinder VariableCompression Ratio (VCR) engine. 通过对多缸可变压缩比引擎使用快速热管理(FTM),该研究应用了基于状态反馈的闭环燃烧控制(CLCC)。
- A group of apprentices were operating the hydraulic press. 一群学徒工在操作水压机。
- A group of apprentics were operating the hydraulic press. 一群学徒正在开动水压机。
- This paper designs multi-servovalve non-symmetric actuator cylinder hydraulic system controlled by the computer which is used in vessel end cold spinning machine with dieless. 对微机控制封头无胎冷旋压机的多伺服阀、非对称油缸的液压系统进行了设计。
- A usually portable device for raising heavy objects by means of force applied with a lever, screw, or hydraulic press. 千斤顶,起重机通过杠杆、螺丝钉或水的压力把重物提起的便携式装置
- The paper introduces acquired air rate of flow in admission pipes and fluidity in cylinder on single cylinder or multi cylinder engines with hot-wire anemometer, and demarcation and adjustment method of measure values are provided. 摘要本文介绍了利用热线风速仪测量单缸与多缸内燃机进气管内流速、气缸内气体流动以及标定与修正的方法。
- Goran Haraldsson,Per Tunestal,Bengt Johansson.HCCI Combustion Phasing with Closed-Loop Combustion Control Using Variable Compression Ratio in a Multi Cylinder Engine[C].SAE Paper 2003-01-1830. 林铁坚;苏万华;裴毅强.;柴油机HCCI燃烧过程中自燃着火和燃烧速率控制的研究[J]
- Designed a set of electro-hydraulic proportional system of forming hydraulic press of heteropolarity multilevel magnetic ring, established the mathematical model of the top plunger cylinder. 3.;设计了极异方型多级磁环成形液压机的电液比例控制系统;建立了上模缸上腔的数学模型。
- high speed multi cylinder line mesh paper machine 高速长网多缸造纸机
- Pascal's law is illustrated by the operation of a hydraulic press, shown in Fig 12-3. 如图12-3帕斯卡定律可用液压机的作用来说明。
- hydraulic press's operating cylinder 水压机工作缸
- CNC Hydraulic Press Brake offers" Conic Bending" up to a maximum of15 mm along the whole length. 电脑数控液压式折弯机提供"锥形折弯"全长尺寸最大可达到15毫米。
- For instance, leisurely desk, hide a hydraulic press compose, table leg bottom is gyro wheel, can drive use. 比如,悠悠桌,暗藏一个液压机构,桌腿底部是滚轮,可推动使用。
- CNC Hydraulic Press Brake offers "Conic Bending" up to a maximum of 15mm along the whole length. 电脑数控液压式折弯机提供"锥形折弯"全长尺寸最大可达到15毫米。
- Dehydration in hydraulic presses is the most general method now in use. 在水压机中驱水是目前通用的方法。
- Hydraulic pump is the power unit of the hydraulic puller (hydraulic press, hydraulic pipe bender, hydraulic jack). 油压泵是油压拉出器(油压机、油压弯管机、油压千斤顶)的动力装置。