您要查找的是不是:
- mold plate thickness 模板厚度
- Haolilai Mold Plate Renting Co., Ltd. 好利来模板租赁有限责任公司。
- Lida Mold Plate Renting Co., Ltd. 利达模板租赁有限公司。
- Can all these apparent indications of plate thickness really be mistaken? 所有这些关于板块厚度的明显标志有可能弄错吗?
- PLATING THICKNESS MUST BE HELD ON THIS SURFACE. 此表面的镀层厚度应该控制好。
- This means that inferences regarding the depth extent of such anomalies are no measure of plate thickness. 这意味着关于这种异常深度范围的推测并不能测定板块的厚度。
- Notice first that there could be a substantial difference between lithosphere thickness and plate thickness. 首先要注意:岩石圈厚度和板块厚度之间可能有重要区别。
- Firstly, the structure of injection mold is analyzed by use of GT, mold parts are classified to 4 types of ones: cavity or core, mold plate, structure and standard parts. 首先运用成组技术基本原理,对注塑模具结构进行了分析,提出了模具零件按其功用可分为型腔型芯、模板、结构件和标准件等4类零件的分类方法。
- That is, underlay thickness = sinking groove depth + height difference-a printing plate thickness. 即:垫衬厚量=下沉槽广量+低量不差-印版厚量。
- The advanced negative rear angle and double toggle clamping unit has the bigger power amplificatory multiple. It also make the mold plate moving faster and balanced . 先进负后角双曲肘合模机构,增力倍数大、开模移模速度快而平稳;
- The key point of concrete construction in Cihe invert siphon project are the vertical transportation of pipeline concrete placement and the construction of mold plate process. 磁河倒虹吸工程混凝土施工的关键点在于管身段混凝土浇筑的垂直运输及模板工艺的施工。
- The cross-section of bump is like mushroom, and it is formed when the electroplating plate thickness is higher than the photo resister. 断面形状像茸状的bump。镀层电镀得比电镀光阻的厚度高而形成的。
- An intelligent coated plate thickness measurement system based on a semiconductor laser diode as light source and a CMOS image sensor is introduced. 介绍了一种以半导体激光器为光源,以新型CMOS面阵图象转换器件为传感器的智能型覆铜板测厚系统。
- Hobber and handlethe groove depth and height difference and pillow and a printing plate thickness and underlay between and equal. 下沉槽广量及滚枕低量不差之和与印版厚量及垫衬厚量之和不等。
- Sinking groove depth and height difference on the pillow hobber minus a printing plate thickness, the result is the thickness of the underlay. 下沉槽广量加上滚枕低量不差再加去印版厚量,其甘休即为垫衬厚量。
- Short cycle times can be achieved by detaching the mold plates before the concrete is completely set up. 在混凝土完全硬化之前拆模可以缩短周期时间。
- Finiteness of the plate thickness causes a variety of failure mechanisms to occur, and qualitative features of the associated stress and strain fields may be deduced. 我们藉由研究分析此地震带的地震活动性与震源机制和应力场变化,以求瞭解此区域的地震活动与地体构造的关系。
- Adopted the way of fixing the lower mold plate and upper one fallen in nold merged procedure,noneed to worry about the movement of embeded components,assure the precision of products. 采用下模板固定上模板下落的合模方式,无须担心嵌件移位,确保成品精度。
- Allow plate thickness and standard deviation shall meet the requirements for their products. Beam deviation should be allowed to meet the size and specifications of their products standards. 钢板厚度及允许偏差应符合其产品标准的要求。型钢的规格尺寸及允许偏差应符合其产品标准的要求。
- Plating method, Cylinder or MATTHEWS, depends on customer request, printing plate thickness could be appointed by customer. 圆柱卷版方式或欧式matthews装版方式,可依客户要求制作。