您要查找的是不是:
- Chen, S.C., Y. C. Chen And N. T. Cheng, "Simulation of Injection Compression Mold Filling Process", Int. comm. Heat Mass Transfer.Vol.25, No.7,pp. 907-917, 1998. 陈裕承;”短射压缩成型之基本探讨与应用”;台湾大学机械工程研究所硕士论文(1996).
- The molding filling process is a very important phase in RTM. 树脂充模是RTM工艺成型过程中的重要一环。
- The mould filling process of rheo-diecasting of semi-solid magnesium alloy and die casting of liquid magnesium alloy has been simulated with the computer program of mold filling process. 摘要利用数值模拟技术,模拟了镁合金液态压铸和半固态流变压铸成形充型流动过程。
- The mould filling process of rheo-diecasting of semi-solid magnesium alloy and die-casting of liquid magnesium alloy has been simulated with the computer program of mold filling process. 利用数值模拟技术,模拟了镁合金液态压铸和半固态流变压铸成形充型流动过程。结果表明:半固态流变压铸成形在不同的内浇口尺寸与位置条件下都可以获得平稳的充型流动场,其工艺参数设计灵活;
- Discussion on the Theory of Mold Filling Process in Die Casting 压铸填充过程的理论探讨
- Study on Display Technique of Vector Field in Mold Filling Process 铸造充型过程中矢量场显示技术的研究
- Influence of the Slack Factor on the Mold Filling Process in Casting 松驰因子对铸造充型过程模拟软件的影响
- Gas Gap Pressure During Mold Filling Process in Expendable Pattern Casting 消失模铸造充型过程气隙压力的研究
- Analysis for Mold Filling Process of Rheo-die-casting of Semi-solid Magnesium Alloy 镁合金半固态流变压铸充型流动过程分析
- NUMERICAL CALCULATION OF GAS-LIQUID TWO-PHASE FLUID FLOW AND DETERMINATION OF FREE-SURFACE FOR MOLD FILLING PROCESS 型腔充填过程中气液两相流计算及三维自由表面的确定
- Study on the Effects of the Slow Shot Phase on the Flow Patterns of Die-Casting Mold Filling Process 压室压射对压铸充型流场影响的研究
- Numerical Simulation of Mold Filling Process for Wax Pattern in Investment Casting 熔模精密铸造蜡模充型过程的数值模拟
- An artificial neural network model for numerical simulation of the mold filling process of EPC 基于人工神经网络的消失模铸造充型过程数值模拟
- mold filling process 充型过程
- V-EPC mold filling process 负压实型铸造
- The mold flow analysis utilizes the computer to simulate dynamic filling process about the injection mold. 模流分析技术是利用计算机对注塑件动态填充过程进行模拟。
- As a close-mold process,it is difficult to observe the mold filling and chemical reaction procedure in the RTM process. RTM为闭模成型工艺,难以观察到模腔内树脂的充模与固化反应过程。
- An adaptive implicit algorithm was proposed for RTM mold filling simulation. 提出了一种基于界面更新的RTM充模分析的自适应隐式控制体积法。
- Verification of a Numerical Simulation of the Mold Filling Processes on Centrifugal Casting of Exhausting Valves of TiAl Based Alloys TiAl基合金排气阀离心铸造充型过程数值模拟的试验验证
- The importance of studying the mold filling velocity of Mg alloy in the expendable pattern casting (EPC) process is pointed out in this paper. 消失模铸造的充型过程对于获得健全铸件至关重要,研究工艺参数对镁合金消失模铸造充型速度的影响,对于工艺参数的优化和铸件质量的提高具有非常重要的理论和实用价值。