您要查找的是不是:
- The transfiguration of effective index method(EIM) is used to analyze the factors influencing the losses, and the minimum bending radius and the relative losses are calculated. 根据有效折射率的变型形式分析了影响弯曲波导损耗的主要因素,并计算了最小弯曲半径及其相对应的损耗。
- At last, the formulation of allowable minimum bending radius limiting the change of the tube-wall thickness is derived, and proved to be of practical value. 推导出限制弯管壁厚变化量的许用最小弯曲半径公式,经试验验证具有一定的实用价值。
- Minimum bending radius for plates 板材最小弯曲半径
- Influence of wall thickness deformation upon the minimum bending radius of bending tube 壁厚变形对弯管最小相对弯曲半径的影响
- minimum bending radius 最小弯曲半径
- minimum bending radius (RBmin) 最小挠(弯)曲半径
- minimum bend radius 最小弯曲半径
- Cycle Life Corrugated metal hose bend radius and minimum acceptable cycle life design requirements are outlined. 循环寿命-波纹金属软管的弯曲半径和可接受的最低寿命周期设计的大纲要求。
- The bending radius of the hose fitting should not be too small. 软管接头部位转弯不要过小,应大于软管内经8倍以上。
- The bending radius should not less than 15 times of cable diameter. 电缆弯曲半径:不小于电缆外径的15倍。
- SIMPLE METHOD FOR ESTIMATING MINIMUM BEND RADII OF SOI SINGLE MODE CURVED RIB WAVEGUIDES 估算SOI单模脊形弯曲波导最小弯曲半径的简单方法
- The bending radius should not be less than 25 times of the cable diameter. 电缆弯曲半径:不小于电缆外径的25倍。
- TUBE DIAMETER SHALL BE WITHIN 10% OF NOMINAL DIAMETER WITHIN BEND RADIUS. 管直径须在直径理论值和折弯半径的10%25以内。
- A reasonable adjustment value of the cable forces was obtained according to judgment criterion of the maximum and minimum bending moment of girders and cable towers. 首先,考虑塔柱和主梁因柔度效应对弯曲能量吸收的权的分配,按最小能量法计算出索力的初值;
- Feature: Anti-bending of hose body, small bending radius, good stiffness, with or without metal fittings available. 特性:管体耐曲挠、弯曲半径小、挺性好。带或不带金属接头。
- Allowed bending radius not smaller than 6 times of its outer diameter, laying temperature not lower than 0. 电缆允许弯曲关径应不小于电缆外径的6倍,敷设温度应不低于0。
- The bending radius of a cable should not be less than 10 times of the cable diameter. 电缆弯曲半径不小于电缆外径10倍。
- The bending radius reduces with increasing length of the mainstream line, and then tends to be relatively stable. 随主流线长度增加,弯曲半径不会无限制减小,将会趋于某一相对稳定状态;
- Excellent pliability, flexibility and elasticity and suitable for special occasions requiring small bending radius. 本产品具有极好的弯曲、柔软性和弹性,可用于弯曲半径较小的场合。
- Permissive bending radius of cable should be no less than 20 times of external diameter of cable. 3电缆的允许弯曲半径不小于电缆外径的20倍。