您要查找的是不是：
- metal removing efficiency 金属切削率
- Let' s take the metal removal rate for example. 让我们以金属切削速率为例。
- The removal efficiency of Am is greater than 99.9%. 对镅的反萃取也作了串级实验(六级反萃;流比BF:BX=1:1);镅的反萃率大于99.;9%25。
- The nicotine removing efficiency of six kinds of cigarette filter have been studied and compared with activated carbon fiber. 研究了6种牌号香烟过滤咀对烟草中尼古丁的吸滤率,并与活性炭纤维进行了比较。
- Dust removal efficiency to meet national emission standards. 除尘效果完全达到国家粉尘排放标准。
- The removal efficiency of FBR can achieve 96.2% of MBR's. FBR处理效果达到MBR工艺的96.;2%25;出水符合城市杂用水水质标准。
- Glass is separated by hand at the dump and ferrous metal removed by magnet. 玻璃在堆放场用手拣出，黑色金属用磁铁分出。
- Metal removeal of bobbin winder's fluted roller is a weak point in our country. 本文提出了用铣削法加工锥形槽筒变螺距，变深度螺旋槽的工艺；
- At present, the cutting velocity and the rate of metal removal have attained to a great height. 在现代切削加工中,切削速度与金属切除率均已达到了很高水平。
- MEX302 -This product is designed for a wide variety of metal removal operations on most ferrous metal and many non ferrous metal. 良好的润滑性能和冷却性能。稳定的结构，长期使用不发臭，有效延长切削液的使用寿命，可用于多数金属的各类加工润滑。
- The removal efficiency of organic pollutant mainly depends on the active biomass of biofilm in the biological pretreatment of drinking water. 摘要饮用水生物预处理过程中，生物膜上存活的活性生物量是有机污染物去除的基础。
- The rapid increase of water temperature in spring induced a decrease of the ammonia removal efficiency. 春季温度的快速升高导致了氨氮去除率的降低。
- However, the rate of metal removal is very small, which limits the use of lasers to hole drilling and cutting operations in relatively thin materials. 不过,由于金属切削量很少,使得激光切削的应用局限于钻孔和较薄材料的切削。
- Metal removal from RMS-8 FCC equilibrium catalyst by HCl,HNO_3,H_2SO_4 and HClO_4 with various concentrations was studied. 用不同浓度的HCl,HNO3,H2SO4和HClO4对齐鲁RMS-8流化催化裂化(FCC)平衡剂的脱金属效果进行了考察。
- COD removal efficiency can reach 79% while the hydraulic residence time(HRT) maintains more than 6h. 稳定运行时HRT为6 h,COD去除率可达79%25以上。
- It was showed that,removal efficiency of NH~+_4-N,TN,and TP by and dominant colony increased with rest time. 结果表明;随停留时间延长;土著生物强化与优势菌群强化对NH4+-N、TN和TP的去除率增加.
- XF: media designed for fast metal removal,deburring &surface improvements.Moderate wear rate but very efficient due to reduced cycle times. 用于快速切削，去毛刺和改善表面质量，尽管有一定的磨损，但由于减少了工作时间，该磨块显的非常高效。
- Experimental result showed that the removal efficiency of COD reached 85.10% when HRT is 18h. 试验结果表明两阶段总的水力停留时间为18h时;COD的去除率最高;达到了85.;10%25。
- VFC：Our most aggressive media formulation where metal removal,radius and cycle times are primary concerns.It's max metal removal in min time. 最具切削力的配方，充分考虑到了工作效率和切削力，倒角性能。它能在最短时间内达到最大的切削效果。
- FBR has high removal efficiency for SS and turbidity, the residual turbidity is lower than 1 NTU. 系统对SS和浊度去除效果极佳,浊度基本在1NTU以下。
