您要查找的是不是：
- melt flow velocity 熔体流速
- Affect the melt flow rate and the cooling speed. 会影响熔体的流动性和冷却速度。
- Flow velocity should not exceed 5 ft./sec. 流速不能超过5英尺/秒。
- High flow velocity was found in some patients accompany stenosis of the siphon. 合并虹吸段狭窄时血流速度增高频谱紊乱。
- The metal flow velocity can become uniformity by optimizing the die structure. 通过对模腔结构的优化设计，使金属流动趋于均匀。
- Strait to the South Central there is a flow velocity of 10 cm / sec around. 海峡中部存在着南向流动，流速为10厘米/秒左右。
- The developing process of CRM of polypropylene melt flow rate has been introduced. 介绍聚丙烯熔体流动速率标准物质的研制过程。
- The crystallinity of polypropylene with different melt flow rate (MFR) are measured by X-ray method. 用X射线法测定了不同熔体流动速率下聚丙烯材料的结晶度。
- The melt flow rate (MFR) impacting to crystallinity and properties of polypropylene (PP) was studied. 研究了聚丙烯(PP)熔体流动速率(MFR)对结晶度及性能影响。
- Peak diastolic flow velocity and CVR before and during infusion of dipridamole were calculated. 测量潘生丁药物负荷试验前后舒张期峰值血流速度及CVR值。
- Melt flow through glass fiber mat during GMT melt impregnation [J].Acta Materiae Compositae Sinica, 2000, 17(3): 28-32. GMT熔融浸渍中熔体在玻纤毡中的流动[J].;复合材料学报;2000;17(3):28-32
- The impaired microvasculature may profoundly affect the coronary flow velocity pattern in the IRA. 结论:微血管床的损害可以影响心外膜冠脉血流动力学。
- Besides,60/40/2/3 HIPS/lPC/PMPI/BCP showed similar melt flow rate and mechanical properties with those of 60/40/3 HIPS/hPC/BCP. 此外 ,共混物 60 /4 0 /2 /3HIPS/lPC/PMPI/BCP与 60 /4 0 /3HIPS/hPC/BCP的流动性以及力学性能也非常接近。
- High resistance waveform with increased flow velocity was seen in contralateral VA. 病变对侧va呈收缩期血流速度增快的高阻力频谱。
- The influences of die radius, load and temperature on the flow properties of FEP melt were investigated by using a melt flow indexer. 应用熔体流动速率仪考察了口模半径、载荷及温度对聚全氟乙丙烯(FEP)流动性能的影响。
- Exhaust fan should be sized to provide enough suction and flow velocity at each of the exhaust point in the laboratory. 排气风机的大小要满足足够的风量和表面风速。
- The melt flow index of the blends was increased when the content of PEEK was decreased and melt temperature was increased. 结果表明：共混物的熔体流动指数随PEEK含量的降低和熔体温度的升高而增加；
- When flow velocity decreases below the corresponding incipient motion condition, no sediment movement occurs. 当水流速度小于相应的起始运动时，将无泥沙运动。
- Factors influencing the graft ratio and melt flow rate of LDPE were studied based on the melt extrusion of methyl acrylic acid (MAA)grated onto LDPE. 通过聚乙烯熔融挤出接枝甲基丙烯酸(MAA),研究了各种因素对LDPE接枝率及熔体流动速率的影响。
- All individuals underwent transcranial Doppler ultrasonography (TCD) with assessment of mean blood flow velocity (MV) in the MCAs. 所有对象都通过经颅多普勒测定大脑中动脉的平均血流速度。
