您要查找的是不是：
- mechatronics of edm plants 电火花设备机电一体化
- mechatronics of spark erosion plants 电火花设备机电一体化
- The article reviews the development of EdM programmes in China through the focus of curriculum development. 本文概述和分析了教育硕士的课程设置及其建设取得的成绩和问题。
- The principles, characteristics, processing laws and efficiency of EDM trepanning cavity of the moulds were analyzed. 分析了电火花套型加工的工艺原理、特点及加工工艺规律和加工效率。
- The EDM(electron discharge machining) dressing pulse power was developed based on the requirement of EDM dressing. 根据电火花修整的需要,研制了电火花修整脉冲电源。
- Two kinds of methods to detect the servo rexsponse time of EDM machine are introduced, the deteition results are given. 介绍电火花成形机伺服响应时间的二种测试方法,结出了测试结果。
- I was founded in 1987, specializing in the production of EDM Machine, drilling legislation, with Saw. 我公司成立于1987年，专业生产电火花成型机床，立钻，带锯床。
- The chain has fallen foul of plants in the water. 链条已和水中的植物缠绕在了一起。
- The basic principle of EDM technology in insulators and machining devices of EDM &WEDM are presented in this paper. 介绍了对绝缘体实施电火花加工的基本原理,以及绝缘体型腔的EDM和绝缘板的WEDM的加工装置。
- Due to a malfunction, the mechatronics of the automatic transmission need to be replaced. After the new mechatronics have been fitted, these do not respond to the SSS (Progman version less than V24). 由于故障;自动变速器的控制单元需要更换。更换新的控制单元后;SSS(版本低于V24)将不能应答。.
- This series are designed to remove the rough surface of mould carved by milling machine of EDM. 本系列锉刀适用于模具及各类有形状要求部位修整的制品.
- The chain has run foul of some plants in the water. 铁链缠在水中的一些植物上。
- The work principle and design method for flexible work tank elevator of EDM machine tool are briefly introduced. 简介了电火花成形机工作油槽柔性升降系统的工作原理及设计方法.
- Frost has killed several of our young plants. 寒霜冻死了我们的几株幼苗。
- The experimental research of EDM process of conductive engeering ceramics using a special power supply by controlling pulse discharging energy, is discussed. 通过专用脉冲电源脉冲放电能量的控制，进行了导电性工程陶瓷材料的电火花放电加工试验研究。
- Coffee beans are the seeds of coffee plants. 咖啡豆是咖啡树的果实。
- Experimental results indicate that pulse current causes denser deposit, which leads to the decrease of EDM tool wear ratio. 当电铸层作为电火花加工电极时，脉冲电流电铸可以降低电极损耗率。
- So that, To analyze the model of discharging, to find the inbeing of PEDM and to promote technology of PEDM practical become Focus of EDM research. 本文通过一组正交工艺实验分析了混粉电火花加工技术各个工艺参数之间的关系,总结了过切量的影响因素,同时对混粉电火花放电点的位置变化规律做了探索。
- In May, all kinds of plants are in full bloom. 五月里各种植物鲜花盛开。
- And draws a conclusion that doped N type monocrystal silicon is quite fit for micro EDM, while a non doped one isn't by a lot of EDM experiments. 对未掺杂单晶硅和掺杂N型硅进行了电火花加工工艺试验,得出了掺杂N型硅有很好的微细电火花加工性能的结论。
