您要查找的是不是：
- master cylinder valve 主缸阀
- master cylinder valve seat 主缸阀座
- Master cylinder bushing at the clutch pedal. 离合器踏板处的总泵衬套。
- master cylinder valve spring 主缸阀簧
- Disconnect brake lines at master cylinder. 拆卸主泵上的煞车线。
- The stove and cylinder valve's copulae, use tie-in double pressurize device. 卡炉与气瓶阀门的接合部位采用接头双重密封装置。
- If user experiences any difficulty operating cylinder valve discontinue use and contact supplier. 如果使用者在操作气瓶阀时有困难,需停止使用,并与供应商联系。
- The hydraulic system comprises a master cylinder and the slave cylinders. 液压系统包括一个主缸和一些辅助缸。
- An acetylene cylinder valve should not be opened more than approximately1 1 /2 turns. 乙炔钢瓶阀门不能开启得超过大约11/2圈。
- Always pressurize a regulator slowly, while standing with the cylinder valve between you and the regulator. 总是站得使钢瓶阀门位于你和调整器之间，对调整器慢慢加压。
- In the third part, based on HCU construction and work theory, the wheel cylinder and master cylinder brake pressure estimation algorithm are discussed. 第三部分主要是在介绍ESP系统HCU具体结构和工作原理的基础上，提出ESP系统制动轮缸压力估算算法，以及制动主缸压力估算算法。
- Always open a cylinder valve slowly. Never crack open a hydrogen cylinder to clear the valve of dust, as the escaping hydrogen may ignite. 总是慢慢地开启钢瓶阀门。由于溢出的氢可能着火，禁止啪地一声打开氢钢瓶。
- Be responsible for new product（Master Cylinder） process engineering development, application, improvement and related documents compiling. 主缸新产品工艺开发、应用、改进工作以及相关的文件编写；
- At the end of the shift or work day, close the cylinder valve and bleed the pressure off the regulator and torch equipment. 在下班或工作日结束的时候，关闭钢瓶阀门，放出调整器和吹管设备内的压力。
- Pneumatic brake and hydraulic brake two-in-one,for air compressors,air brake master cylinder,wheel cylinder,door pump,cluth,booster,wheel cylinder,etc. 集气压、液压制动综合为一体;可对空气压缩机，气制动总泵，分泵，门泵，离合器，助力器，液压制动主缸，轮缸等各类制动附件进行试压试验
- Recommended Closing Procedure: Close the cylinder valve tightly using a gloved hand. 推荐的关闭程序：用戴手套的手紧紧地关闭阀门。
- A hydraulic cluth linkage typically includes a cluth master cylinder and reservoir, a hydraulic line and a slave cylinder. 液压离合器杆系一般包括一个离合器主缸和储液罐，一根液压管路和一个工作缸。
- Multi 10-plate wet clutch uses a new Nissin hydraulic master cylinder for easy, consistent lever pull and automatic adjustment of the free play. 10多片湿式离合器采用了新的日清液压主缸的简单，一致的杠杆拉动和自动调整的**发挥。
- This partition should extend from the top of the panel to18 inches below the cylinder valve. 隔离物应该在钢瓶阀门下面，从控制板顶部伸出来18英寸。
- If user experiences any difficulty operating the cylinder valve, discontinue use and contact supplier. 如果用户在操作钢瓶阀门时遇到任何困难，停止使用，联系供应商。
