您要查找的是不是:
- The principle of a CNC cutting machine for intersecting line and the design of CNC software are introduced which incorporates the integral linear interpolation algorithm to achieve the trace control of a intersecting line cutting machine. 阐述一种计算机数控相贯线切割机的轨迹控制原理及数控软件设计,采用数字积分直线插补算法来实现相贯线切割机的轨迹控制。
- Trajectory planning of robot was also researched. In this paper, path planning algorithm in the joint space and two kinds of linear interpolation algorithms in the Cartesian space were introduced. 本文还研究了机器人轨迹规划技术,讨论了SCARA机器人的关节空间轨迹规划算法和笛卡儿空间的两种直线轨迹插补方法。
- Influence of different linear interpolation algorithm on root mean-square power in brain electrical activity mapping 不同线性插值方法对平均平方根值脑电地形图的影响
- Application of the Optimal Non-Equidistant Linear Interpolation algorithm in Thermistor Temperature Measurement 最佳非等距线性插值算法在热敏电阻测温中的应用
- Linear Interpolation Algorithm Based on the Intermediate Contour of Intracerebral Brain Hemorrhage CT Image 基于颅内出血CT图像层间轮廓线的线性插值算法
- A simple algorithm for multi axes general linear interpolation is introduced. 提出了一种用于多坐标轴广义直线插补的简易算法。
- Uses linear interpolation to create a color value. 创建两种颜色间的线性插值颜色;
- Linear Interpolation Algorithm 直线插补算法
- The traditional method is decimation and linear interpolation. 传统的改变图像空间分辨率的办法是抽取和线性插值。
- A sub-pixel matching algorithm was developed based on phase linear interpolation assuming a linear phase distribution between adjacent pixels. 根据相邻像素相位近似线性分布的特点,提出了一种基于相位线性插值的亚像素匹配算法。
- The paper gives three advised algorithms: 1) The linear interpolation and transform domain interpolation algorithms are replaced by the spline cubic and MMSE algorithms to reduce the complexity of achieving the transfer function; 本文的主要工作是提出了三种 OFDM 系统的信道估计改进算法:1)使用了新的插值方法的改进算法:针对线性插值算法估计误差较大,而基于变换域的插值法计算量太大的特点,利用三次样条插值算法和最小均方误差(MMSE)方法代替线性插值和基于变换域的插值算法对信道进行估计;
- I write the numerical analysis curriculum designs the source code, here is the value interpolation algorithm content. 我自己写的数值分析课程设计的源代码,这里是数值插值算法的内容。
- We obtain an upper bounded estimate for the convergence rate of the piecewise linear interpolation. 摘要给出了分段线性插值收敛速度的一种估计。
- An interpolation algorithm for Non Uniform Rational B-Spline (NURBS) curve to control redundancy error was proposed. 摘要提出了一种能有效控制冗余误差的非均匀有理B样条曲线插补算法。
- A direct interpolation algorithm for spatial curves on a surface is proposed for pen-cutting of sculptured surfaces. 摘要针对复杂曲面笔式加工时位于曲面上的空间曲线型刀具轨迹,给出一种直接插补算法。
- The linear interpolation in use is generally the one which is constructed easily, but it is low in efficiency. 由于通常使用线性插值作为插值算子,虽然线性插值容易构造,但计算效率一般。
- The low-order linear interpolating will incur more aliase noise. 用低阶的线性内插会带来较大的镜像噪声。
- In addition we give our implementation on the interpolation algorithm in the testbed. 还介绍了在实验平台中所采用的一种高效率的内插算法。
- Finally, a parallelogram linear interpolation was made along the edge directions in edge regions after a phase mapping. 最后在边缘区域内边缘方向进行相位映射后,进行平行四边形线性插值。