您要查找的是不是：
- Jig Jaw Clamping Force and Cylinder Clamping Capacity Calculation for Forging Manipulator 锻造操作机钳口夹紧力和夹紧缸能力的计算
- jig jaw clamping force 钳口夹紧力
- Clamping force equalization: same force to two workpieces in different size. 自动补偿机构：不同大小工件，可在同时夹紧，且夹持力相同。
- Size and grade specific cap bolts offer superior clamping force between the cap and base. 座罩螺栓有不同的尺寸和等级,在座罩和基础之间形成理想的夹持力。
- In using an injection moulding machine, it is best to use the minimal but adequate clamping force F. 使用注射成型机，最好使用最小同时充足的锁模力F。
- The two deices do clamping force measurement/control and caity pressure switchoer to holding pressure. 这两个装置就是锁紧力量测/控制装置和（射出）转保压的模腔压力转化装置。
- Choosing a PIMM simply on the basis of shot weight is too simplistic.Neither is clamping force alone sufficient. 仅仅基于射出重量去选择注塑机是不够的，同样的，仅考虑锁模力也不可以。
- Furthermore, a high clamping force compresses the toggles and the mould, and stretches the tiebars, reducing the fatigue lives of the toggle pins, the mould and the tiebars. 高锁模力对曲轴结构和模具产生挤压，对拉杆（控制开合模甚至锁模的四个大杆）产生拉伸，从而降低他们的疲劳寿命。
- An excessive clamping force distorts the mould and the mould cavity unnecessarily, affecting the precision of the moulded part. 过大的锁模力会使模具以及模腔产生不必要的变形，影响成型品的精度。
- This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method. 针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟,得到径向位移、接触应力、锥面间隙结果。
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- I hit him fair and square on the jaw. 我不偏不倚打中他的下巴。
- Twoprocess mode can be ed, single or continuous. The clamping force of hold down device will in crease when cutting force increases. 两种使用模式给客户选购，单次或连续。另压片力会随着剪切力增加而自动调节。
- This very reasonable action triggers the trap, and the steel jaws clamp down hard on his leg. 这个非常合理的操作触发了那个陷阱，用户又遇到了新的打击，他被一个粗鲁的如图17-3所示的对话框所拒绝。
- Its paper clamp presses tightly against the material to be cut by means of a high quality strong pull spring assembly and the clamping force can be adjusted readily. 压纸器是由优质强力拉簧组使其牢牢地压紧裁切物,压力大小调整方便。
- The mechanics models of metal-bands transmission concerning clamp force of pulley, axial force, thrust and tension is built based on Coulomb friction theory. 以库仑摩擦理论为基础，在考虑了带轮夹紧力、轴向力、挤推力和金属环张力的基础上，建立了金属带传动的力学模型。
- The alterable clamping force fixture can automatically adjust its clamping force to adapt to the cutting force to reduce the cutting deformation of machining system. 变夹紧力夹具能够适应切削力的变化,自动调整夹紧力的大小,以减少加工系统的切削变形。
- They watched jig on TV and tried to imitate. 他们看着电视里的快步舞并且试图模仿。
- Insufficient clamping force gies rise to flash at the mould joint.Most PIMMs today use their clamping force (in tonnes) in their model name, e.g.ME125III. 锁模力不足会引起模具结合处的飞边，现在大多数注塑机都采用其锁模力（单位：吨）作为其型号名称，如：ME125III。
- I hit the man fair and square on the jaw. 我不偏不倚击中了那个人的下巴。
