您要查找的是不是：
- iterative control algorithm 迭代控制算法
- Extracting data from multiple sources requires an iterative control flow. 从多个源提取数据需要采用迭代控制流。
- Correct control algorithm is the key of network congestion control. 因此,正确的控制算法是网络拥塞控制的关键。
- The control algorithm uses the increase type PID control algorithm. 系统实时性和控制精度较高。
- PID control based on iterative control compensation is used in position control part. 在位置控制部分,采用了基于重复控制补偿的PID控制方法。
- So the adaptive character of the control algorithm has been enhanced. 将该算法应用到电控气动离合器操纵系统中并进行实验。
- An intelligence PID control algorithm based on the expert system was discussed. 讨论了一种基于专家知识的智能PID控制算法。
- The proposed controller consists of an iterative control compensation and a conventional PID controller. 用重复控制作为误差补偿与传统简单的PID控制器相结合作为位置控制部分所采用的控制算法。
- Stability condition of the proportional control algorithm is given for a fixed target. 针对固定目标，文中给出了比例控制算法的稳定性条件。
- The system is composted of a high accuracy thermocouple and a 8031 single chip computer while adaptive PID control algorithm is employed. 该系统由一个高精度的热电偶和8031单片机组成，采用自适应PID控制算法。
- A new parameters adaptive PID control algorithm is put forward on the basis of Cohen Coon assignment formula. 在Cohe Coon整定公式的基础上 ;提出了一种参数自适应PID控制算法 .
- First, the TCP theory and the key technology of TCP congestion control algorithm are researched in the thesis. 首先,对Internet中传输控制协议的原理以及TCP拥塞控制算法中的关键技术进行了深入探讨和研究。
- First, the jitter control algorithm aims at smoothing the jitter variance with low queueing delay latency. 首先，延迟变异控制机制目标在低延迟代价条件下，减缓延迟变异。
- closed-loop P type iterative control 闭环P型迭代控制
- On this basis, the basic model of main-shaft-less concave printer and ADRC are combined to get a new control algorithm. 在此基础上又将推导出的无主轴凹印机粗基本模型与AD-RC相结合，得出新的控制算法。
- For to evaluate the various control algorithm, Spencer, et al. present a AMD benchmark model. 为了能对各种算法有一个公认的评价标准，美国Notre Dame大学Spencer研究组通过对主动质量驱动(AMD)控制的三层框架模型实验的数据分析，建立了AMD控制Benchmark模型。
- Fuzzy control algorithm is programmed by Borland C++, control of inverted pendulum hardware system is realized. 利用Borland C++编写模糊控制算法程序，实现了倒立摆实物系统控制。
- It is important to develop the ABS ECU, study the control algorithm of ABS, and validate control logic of existing ECU. 它对于ABS ECU的开发、ABS逻辑的研究、验证ECU控制策略的合理性及实用性都是很有效的工具。
- Analying the influence of output transform to NNC control algorithm in neural-PID control. 对神经PID控制中,输出转换成过程对NNC控制算法的影响进行了讨论,使神经PID控制在各种情况下得以正确应用。
- This paper presents a model predictive control algorithm for affine nonlinear systems. 摘要本文提出一个用于仿射非线性系统的模型预测控制算法。
