您要查找的是不是：
- interlaminar interface bonding 层间界面结合
- Indirect methods to measure the interface bond strength include the interlaminar shear strength test. 测量界面粘结强度的间接方法包括层间剪切强度试验。
- The log decrement are suitable for determining interface bond damage. 对数衰减率适宜于测定界面粘结的破坏。
- The effect of silane and titanate coupling agents on the interface bonding state and the mechanical properties of GRPFN (Glass Fiber Reinforced PF Nylon)has been studied. 研究了几种硅烷偶联剂、酞酸酯偶联剂对玻纤增强PF尼龙界面粘结状态和力学性能的影响。
- Interface bonding strength of clad transition joints welded in two different welding procedures is compared and a proper welding procedure is determined. 对两组不同焊接规范下复合过渡接头的界面结合强度进行了对比，确定了合适的焊接工艺参数。
- The effects of particle volume fraction, tensile rate and interface bonding strength on the properties of GB/HDPE composites were studied by tensile test and SEM observation. 通过GB／HDPE的拉伸实验和断口形貌分析，研究了颗粒体积分数、拉伸速率、界面强度对GB／HDPE复合材料力学性能的影响。
- The continuous, high strength and fast construction is the construction characteristics of RCC dam and also is the fundamental guarantee of interface bond quality. 摘要连续、高强度、快速施工既是碾压混凝土坝的施工特点，也是层间结合质量的根本保证。
- The relationship of interface temperature and interface bonding strength of aluminum alloy-steel transition joints in welding is analyzed through simulative heating treatment tests. 摘要通过模拟热处理试验，分析了焊接时界面温度与界面结合强度的关系。
- There exist the weak interfaces bonding strength between the vinylon fibres and matrix material. 纤维和基体间界面结合强度较弱。
- It indicates that the interfacial bonding of new to old concrete has good shearing property. 结果表明，沟槽式新老混凝土粘结面具有较好的抗剪性能。
- The fracture surface of the wires studied by scanning electron microscopy (SEM) shows a suitable interfacial bonding between the fiber and aluminum. 复合丝拉伸断口的扫描电镜(sem)观察可见断面有一定起伏，部分纤维拔出但长度较短，表明纤维与基体具有适当的界面结合。
- They observed that broken fibers recede within the matrix in composites with weak interfacial bond. 他们观察到弱界面粘结的复合材料，断裂的纤维会在基体中缩回。
- The results showed that the interfacial bond could appreciably enhance when the strength of repair materials increased. 在修补材料中掺入纤维会明显提高界面结合强度,且聚丙烯纤维要优于碳纤维。
- The toughening efficiency was related to morphology, interfacial bonding, thermoplastic particle deformation and matrix deformation of the system. 体系增韧效果与相态结构、界面粘合、热塑性粒子的延展性和双马基体的延展性有关。
- Bending strength, compressive strength, interfacial bond strength and frost-resistance are also studied and analyzed. 并对修补混凝土的抗折、抗压、新老界面粘结强度以及抗冻性等进行了试验研究。
- Adding Mo can improve the interfacial bonding between the Hadfield steel and TiC, and the best adding ratio between Mo and TiC is 1:3.68. 添加Mo元素能改善TiC与高锰钢界面的润湿性，其中Mo的最佳添加量是Mo与TiC的质量分数比为1：3.;68。
- The strongest interfacial bond could be achieved the moment that the addition ratio of AWA was 6 %( by weight). HEA-JL型抗裂防水剂的掺量为6%25时，界面结合紧密，界面结合强度高，有利于防水抗渗。
- Keywords compound ultrafine fibers;co-axial electrospinning;interlaminar interface;composites;bending property;interlaminar shear strength;impact toughness; 复合纳米纤维;同轴共纺;层间界面;复合材料;弯曲性能;层间剪切强度;冲击韧性;
- The results showed that the pigments and fillers whose surfaces were amphibious could be dispersed finely,and the interfacial bond was strong in c... 结果表明,用两亲性高分子改性颜填料在乳液中的分散性良好,与聚合物界面粘结强。
- The results suggeste both kinds of functionalization method can improve the dispersion of CNTs and enhance the interfacial bonding between them and matrix. 结果表明通过这两种功能化的方法，有效的提高了碳纳米管在基体中的分散性及其与基体材料的界面作用力。
