您要查找的是不是：
- interference fit amount 过盈量
- Bearings with a tapered bore are always mounted with an interference fit. 带圆锥孔轴承始终以过盈配合安装。
- FEM stress analysis of assemble symmetrical body of interference fit. 过盈配合组合轴对称体有限元法应力分析
- Therefore, the ring need not necessarily have an interference fit unless this is required for other reasons. 因此,轴承圈不一定要有过盈配合,除非因其它原因需要这样做。
- For bearings having a tapered bore, inner rings are always mounted with an interference fit. 对于圆锥孔轴承,内圈的安装始终采用过盈配合。
- Alignment needle roller bearings should have an interference fit in the housing bore. 对中滚针轴承的轴承座孔应过盈配合。
- The bearings are generally mounted with an interference fit on the roll necks and therefore often have a tapered bore. 轴承一般以过盈配合安装在轧辊轴颈上,因此经常带锥形孔。
- Research on interference fit riveting, composites structure riveting and driving interference-fit fastener have been done. 对电磁铆接技术在干涉配合铆接、复合材料结构铆接、干涉配合紧固件安装方面的应用进行了系统研究。
- But the interference fit by hydroform result in the damage occurring on the contact surface. 然而,由于锥套与辊颈利用液压胀形实现过盈装配,使得接触面间在装配过程中发生表面损伤。
- The interference fit between the gate and seats provides bubble tight shutoff, even under the lowest pressure. 即使在最低压力条件下，闸板和阀座之间的交互界面也能够实现气密性关闭。
- The interference fit between the gate and seat provides bubble tight shutoff even under the lowest pressure. 即使在最低的管线压力下，闸板与阀座之间的配合也能够实现气泡级密封功能。
- Bearings with a tapered bore are used when an interference fit is required for the inner rings on the roll neck, e. G. When rolling speeds are high. 在轧辊轴颈上的内圈需要过盈配合时,例如轧钢速度高时,使用带锥形孔的轴承。
- Interference fit is required between outer ring and housing as the load is varying in direction relative to the outer ring. 外圈与轴承座之间需要过盈配合,因为相对于外圈的负荷方向有变化。
- The process problems of composite structures using interference fit technology can be solved by use of Stress Wave Riveting (SWR). 分析了复合材料结构采用干涉配合技术存在的工艺困难，利用应力波铆接设备对碳纤维复合材料进行了干涉配合铆接试验，并对铆接质量进行了检测分析。
- The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3. 锁紧螺母扭矩压紧垫片时，其与垫片的最大相互作用力不能超过表3所给扭矩值。
- To dismount a bearing having an interference fit, the tools described in the following section may be used, the choice of tools will depend on bearing type, size and fit. 拆卸过盈配合的轴承,可使用下述各种工具,而工具的选择取决于轴承类型、大小和配合。
- Based on that,further analysis found regression curve is closely exponential function y=6.874e-4.604x in correlation between wood density and optimal value of interference fit. 在此基础上;进一步探讨最佳过盈配合量与木材密度的相关性;得到其回归拟合曲线近似为指数函数y=6.;874e-4
- For a high speed motorized spindle, the interference fit between the shaft and bearing has a great influence on the stiffness,rotary accuracy and life of the spindle. 高速电主轴轴承与转轴配合的过盈量大小对主轴的刚度、旋转精度和使用寿命具有十分重要的影响。
- It points out emphatically that this technique dispels the stress of draw roller by interference fit,and applies to differ-endt kind of high speed drawing frame. 着重指出这种热粘合无套差的并条胶辊彻底克服了有套差引套胶辊的应用紧张状态,完全满足高车速、重加压的工艺要求,可在进口及国产的各种高速并条机上使用。
- These formulas contribute to design the interference fit for the high speed spindle, improve the kinematical performance and the machining performance of the spindle. 上述公式的推导有助于高速主轴过盈联结的设计,提高主轴的运动特性和加工特性。
