您要查找的是不是：
- inlet valve spring 进给阀簧,吸油阀簧
- Remove valve spring and retainer. 拆卸阀弹簧和扣件。
- The tightness test of inlet valve for emergency fire pump. 应急消防泵进水阀密性试验。
- CAUTION: The check valve spring is in compression. 警告：止回阀弹簧处于压缩状态。
- Close the cold water inlet valve and open a nearby hot water faucet. 关闭冷水进水阀，打开附近的热水水龙头。
- For removal of valve stem seal and lower valve spring guide. 可用于拆卸汽门油封或降低汽门弹簧。
- Lift retainer and check assembly from valve body. To assist with removal a small flow can be applied by "cracking" the inlet valve slightly. 从阀体内取出固定器和止回模块。可以通过稍微“开裂”阀门进口来帮助清除少量的流体残留。
- To assist with removal a small flow can be applied by "cracking" the inlet valve slightly. 为了有助于拆卸，可以通过轻微"分裂"阀门进口来产生一小股流体。
- When the piston nears the top of this stroke, the inlet valve is opened and the exhaust valve closed. 随着曲轴转动，复又向上带动活塞，同时废气经由气缸头盖上的排气阀排出。
- If the drain hose does not have this rating, open the cold water inlet valve and open a nearby hot water faucet until water is no longer hot. 如果排水软管的额定温度没有达到上述要求，请打开冷水进水阀，打开附近的热水水龙头，直到水不热为止。
- The outlet valve of the plunger pump must be taken down before the inlet valve is hauled out with the former disassembling instrument for the valve. 柱塞泵的下凡尔损坏后,用原来配的凡尔拔出器拆卸时要先拆掉上凡尔,再拆卸维修下凡尔。
- Due to the release of pressure when removing the cover, the relief valve spring may eject quickly. 因为在拆卸阀盖时松开压力，安全阀弹簧可能会快速弹出来。
- SPRING COVER FR INLET VALVE SPINDLE 进气伐杆弹簧盖
- Multi - purposed optimal design of reliability for valve spring based on fuzzy method. 基于模糊学方法的气门弹簧可靠性多目标优化设计。
- If the valve fails to completely reset and continues to release water, immediately shut off the cold water inlet valve, and call a qualified service technician. 如果阀门无法完全重置，并继续释放水，则要立即关闭冷水进口阀门，打电话叫有资格认证的工程师。
- Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring. 拆卸安全阀阀盖，阀杆/隔膜总成，和安全阀弹簧。
- Chemical analysis and mechanical tests on the materials used for inlet valve body, disk, trunnions, servomotor cylinders, piston rods, upstream and downstream piping. 对用于进气阀阀体、阀盘、耳轴、伺服缸、活塞杆及上下游管道的材料进行化学分析和机械测试。
- Meanwhile, the problem of fast open/close of air inlet valve during air surge backwash and some default of equipment was successfully solved during commissioning. 在调试中，解决了水气反洗时要求进气阀快速开／关等问题。
- Install a dial indicator so plunger contacts valve spring retainer as nearly perpendicular as possiblZero the indicator. 安装一个表盘式指示器，使柱塞与气门弹簧护圈尽可能垂直。将指示器调零。
- Check whether or not the fuel injection pump plunger and fuel outlet valve is worn or clogged, plunger spring and fuel outlet valve spring is broke. 喷油泵柱塞及出油阀是否磨损或卡死、柱塞弹簧及出油阀弹簧是否折断；
