您要查找的是不是：
- inlet and outlet flow passage 进出水流道
- Mathematical Model Calculation and Analysis of Inlet and Outlet Flow Passages and Setting Height for the Taiqu River Pump Station 太浦河泵站进出水流道及安装高程数模计算分析
- To perform an internal analysis all the model openings must be closed with lids, which are needed to specify inlet and outlet flow boundary conditions on them. 执行内部的流体分析过程，模型开口必须用盖子封闭起来，这就需要在模型上规定入口和出口的流动边界条件。
- It includes the optimization of the inlet and outlet flow angles, the moulding design, checking of the design quality, the performance prediction of the turbodrill, etc. 它包括:涡轮叶栅进、出口角的优化设计;涡轮叶栅的解析法造型设计;涡轮叶栅设计质量的检验以及涡轮性能参数的预估等。
- It's better to put letters at the inlet and outlet. 最好在进口和出口处标上字母。
- Close valves at both inlet and outlet ends. 进、出水端阀门关上。
- Provide steam rings for tube side inlet and outlet flanges. 管程的入口与出口法兰配备蒸汽环。
- INVESTIGATION INTO EFFECT OF TIP CLEARANCE ON INLET AND OUTLET FLOW FIELD OF DIANGONAL IMPELLOR WITH EXIT GUIDE VOLUTE AT NEAR STALL CONDITION 近失速工况下叶顶间隙对后置蜗壳斜流叶轮进出口流场影响的实验研究
- Shape, size, site, color, and inlet and outlet slope of page nexto page. 页连接符号的形状、大小、位置、颜色、进出箭头。
- At the same time the inlet and outlet of the impeller and the guide vanes were measured by using five-hole pellet flow dynamic probe. 采用五孔圆球流体动力探针对叶轮及导叶进出口流场进行了测量，给出速度和压力分布图。
- In the numerical simulations of flow in twin screw extruders, imposition of boundary conditions on the inlet and outlet of the flow domain has long been a controversial problem. 在对双螺杆挤出机流场的数值模拟中,流道进出口边界条件的设置一直是一个颇具争议的问题。
- The size of inlet and outlet of HPT are 3”, while the inside diameter of Coriolis mass flow meter is smaller so that there will occur high pressure drop. HPT进出口为3”，科氏力质量流量计内径更小，有可能出现憋压，但停留时间不足0.;5分钟。
- Continuous flow and continuous product discharge because of the defined mixing distance in a horizontal drum between inlet and outlet of the mixer. Every particle has the same retention time. 由于混合机水平滚桶的入口和出口有确定的混合距离;因此混合机可以实现连续混合;并连续卸料.;每个颗粒都有相同的混合时间
- The oil pump should be firmly fixed; the inlet and outlet pipe should be fastened without loose. 油泵应牢固地加以固定,进出口管接头,不得有松动现象。
- Causes of the stray current corrosion in inlet and outlet of the electrolytic bath were analyzed to put forward a solution. 分析了电解槽进出口系统各主要设备杂散电流产生原因，提出了针对性的解决方案。
- Specification is 3/4-3 ins. Inlet and outlet is screw thread joint. Used for Pulse-dust-cleaning system. 规格有3/4-3英寸，进出口为螺纹连接，最适用于脉冲清灰系统上。
- Effects of blade negative bowing on secondary flow, total pressure loss and outlet flow angle were analyzed quantitatively, mechanism of the effects was discussed as well. 定量地分析了叶片反弯曲对叶栅出口二次流、总压损失和气流角的影响，并探讨了叶片反弯曲作用的机理。
- Meantime assumed that, the variation of the fluid within the inlet and outlet of pump is a isoth... 在计算泵提供给气体的扬程时给出了三种算法,并对实例计算结果进行了分析比较。
- Use the cavitation chart and determine if the intersection of the inlet and outlet pressures falls in the shaded area. 采用空穴图表并且确定进口和出口压力的相交是否落在阴影区域内。
- Copy the serial number of your glaze line on the scutcheon above the glaze line inlet and outlet. 按钉在施釉线进出口上方标牌抄下你的施釉线系列号。
