您要查找的是不是：
- There is a time lag of about 10 years. 有大约十年时间的间歇。
- injection time lag 喷射时间滞后
- Increasing the total time lag is destabilizing. 增加总时滞将使稳定性降低。
- There is a time lag of about fifteen years. 时间上有一段约15年的间隔。
- Specifies the time lag between two consecutive historic models. 指定两个连续历史模型之间的时间间隔。
- No. Time lag is not from schedule result, is from input. 不是。延时是从数据输入，不是计算结果。
- There is a long time lag between when I do the work and when I get paid. 我做工作和领薪水之间相隔很长一段时间。
- For more general application the double time lag model should be used. 对于更一般的应用，应当采用双肘滞模型。
- There is a difficulty in measuring the time lag with sufficient accuracy. 要足够准确地测量时间间隔期有一些困难。
- Checking of each cylinder injection timing with static. 静态检查各缸供油时间。
- The lab must be able to carry out routine tests with a minimum of time lag between sampling and testing. 实验室必须能够在取样以后一个最小间隔时间内完成常规检验。
- Right here the MKB software calculates the perfect injection time, duration and boost pressure. 就在这里，MKB软件精确计算燃油喷射点、持续时间及喷射压力。
- Hopefully this time there's not nearly that same time lag between seeing a social imperative for it to be pervasive. 这次有希望的几乎有不相同的时间在为它看见社会的命令普遍之间落后。
- There is in many species a time lag between flower initiation and an irreversible commitment to flower. 许多种植物，从花的孕育到花的开放之间有一段时间滞差。
- Judgments are more consistent if one can observe the same trait on different plots with little time lag. 假如人们不拖延时间，逐个小区地观察同一性状，判断会更加准确。
- The lab.must be able to carry out routine tests with a minimum of time lag between sampling and testing. 实验室必须能够在取样以后一个最小间隔时间内完成常规检验。
- Based on the numeric analysis of the model, the effects of melt temperature, injection time, mold temperature and pre-filled volume on the cell size were studied especially. 在对该数学模型进行数值分析的基础上,着重研究了熔体温度、注塑时间、模具温度、初始填充量对微泡尺寸的影响。
- The time lag between the direct wave and the scattered wave could be computed by using the simplex algorithm method. 当弯曲波在传递时遇到平板裂缝则会产生散射波，因此含有裂缝平板的板波讯号即包括弯曲波的直接波传与裂缝引起的散射波传。
- This model took the parameters of engine speed, fuel pump rack position, pedal, LPG injection time, cooling water temperature and torque as the input variables. 模型将转速、油泵齿条位置、油门开度、LPG喷气时间、冷却水温度、转矩作为输入变量。
- What fascinated me was the time lag between the issue of my instructions to the ship and the ship's response. 使我极感兴趣的是，我向船发布命令和船做出反应当中的时间间隔。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
