您要查找的是不是:
- The housing bore seating should be sufficiently wide so that after mounting there should be about 1 mm from the mounted washer to the edge of the housing bore (fig 3). 轴承座内孔座合面应足够宽,使得在安装后,从安装好的垫圈到轴承座内孔的边缘应有约1mm(图3)。
- housing bearing seat 箱体轴承座
- Carry on the craft reform to bearing seat and axis of the belt conveyer supporting roller. 对带式输送机的托辊的轴承座和轴进行工艺改革。
- The compound bearing installed between the headstock and bearing seat does need any lubrication. No wearing. 主轴和轴座间安装有自润滑轴承不用加油,没有磨损。
- According to the structure feature of bearing seat product, design a three-plate type mold structure whose mould cavity is compulsive demolding. 根据支承座产品的结构特点,设计了一种型腔强制脱模的三板式模具结构。
- The new housing bears witness to the energy of the Council. 这些新建的住宅是议会具有能力的证明.
- Use care not to score the housing bore when prying out seals and washer. 当拆下油封和垫圈时,要特别小心切勿划伤机座孔。
- In SKF roller bearing units the necessary axial displacement occurs between the bearing outer ring and its seating in the housing bore. 在SKF滚子轴承单元中,轴承的外圈与其在轴承座孔中支承面之间会发生必要的轴向位移。
- To ease installation it is recommended that the housing bore should have a lead-in or chamfer as shown in fig 3. 为便于安装,建议轴承座内孔应有一引导进入的倒角,如图3所示。
- The title deed for the house bears date November 5,1988. 房契签署的日期是1988年11月5日。
- CARB bearings are non-locating bearings and must be secured axially in the housing bore using locating rings. CARB轴承只能用做非定位轴承,并且需要用定位环从轴向固定到轴承座的孔中。
- Tapered bearing seatings are checked using ring gauges, special taper gauges or sine bars. 圆锥形轴承基座则采用环规、专用锥度规或正弦规检查。
- The title deed for the house bears date November5, 1988. 房契签署的日期是1988年11月5日。
- Alignment needle roller bearings should have an interference fit in the housing bore. 对中滚针轴承的轴承座孔应过盈配合。
- The title deed for the house bears date November 5, 1988. 房契签署的日期是1988年11月5日。
- Interestingly, a local manor house bears the name of Owlpen Manor. 有趣的是,当地有一个别墅叫“猫头鹰栏庄园”。
- With the oil injection method, oil under high pressure is injected between the bearing and bearing seating to form an oil film. 采用注油方法,油在高压下注入轴承和轴颈之间,形成一层油膜。
- The attachment bolts can be preloaded to give better location and cannot deform the housing base or housing bore. 连接螺栓可以预加载,以更好地固定,不能使轴承座的底座或轴承座孔变形。
- The structural characteristics of heat pumps:From the pump, gear, bearing seats, valve, bearing and seal unit with horizontal rotary pumps. 高温泵的结构特点:由泵体、齿轮、轴承座、安全阀、轴承及密封装置组成的卧式回转泵。
- They can be pressed into the housing bore directly.Linear ball bearings are only suitable for linear motion. 直线运动球轴承只能用于直线运动,不能作为旋转运动部件的支承。