您要查找的是不是：
- hot spinning temperature chart 热旋压温度图
- The spinning temperature should be well controlled to control melt viscosity during PTT production. 在PTT生产中，应严格控制纺丝温度，通过温度来调节熔体粘度。
- To insure the spinning temperature,the interspace of pipe blank and mold is less than or equal to 0. 要确保旋压温度,管坯的长度在成品倍尺内取短倍尺,管坯内径与芯模之间的间隙不大于0。
- For detailed Operating Pressure, refer to Pressure Temperature Chart on pages 91. 如果需要工作压力的细节,请参阅第91页的压力温度表。
- For detailed Operating Pressure, refer to Pressure Temperature Chart on pages 71 and 72. 如果需要工作压力的细节,请参阅第71和72页的压力温度表。
- A high spin temperature, for example, would indicate that a high fraction of atoms were aligned. 例如，高自旋温度代表较高比例的原子，具有相同方向的自旋排列。
- It is found that the matrix-fibril morphology of blend fiber is relating intensely with spinning temperature, but weakly with spinning speed. 纤维的岛相分布与纺丝温度相关性强，而与纺丝速度的相关性弱。
- The main effect factors bringing about brittle fracture of wire rod without drawing are carbon content,spinning temperature,speed of cooling control and contents of baneful gas. 盘条未经拉拔出现脆断的主要影响因素是碳含量、吐丝温度、控冷速度和有害气体的含量;
- Effects of two components' melt index, spinning temperature, lateral blowing, drawing ratio, crimping and heat setting on fiber quality and properties are discussed. 讨论了两种切片的熔融指数、纺丝温度、侧吹风、后拉伸倍数、卷曲、松弛定型工艺对产品质量及性能的影响。
- Results Defects were found in temperature chart,medical order,admission evaluation chart,nursing record,and discharge evaluation chart and accounted for 3.6%,4.4%,5.8%,6.4% and 5.0%,respectively. 结果体温单、医嘱单、入院评估单、护理记录单和出院评估单发现缺陷各占3.;6%25、4
- TCS one|step process was employed to produce 57 dtex/36f super bright triangle PET FDY. The effects of drying step, spinning temperature and velocity, quenching conditions, and thermal channel temperature on fiber quality were discussed. 用热管纺丝拉伸一步法 ( TCS)生产 5 7dtex/36f涤纶超有光三角形 F DY ,探讨切片干燥、纺丝温度、速度、冷却条件、热管温度等对产品质量的影响。
- The equipment,raw material and technology for producing 50dtex/34f polyester interlaced bright trilobal set yarn are described,with focus on the spinning temperature,package formation in winding and the control of tenacity with elongation. 本文介绍了50dtex/34f有光三叶涤纶低弹网络丝的生产设备、所用原料及工艺参数;着重讨论了纺丝温度、卷绕成形及强伸度的控制问题.
- Based on production actuality of Nylon 6 HOY, how to set spinning temperature to adapt the change of chip's viscosity, chip grain fineness and screw extrude volume was discussed in this paper. 根据锦纶6HOY的生产实践就纺丝温度的设定如何适应切片粘度、切片粒度和螺杆挤出量的变化进行了探讨。
- The effect of some factors, such as quality of chip. water content of dry chip. spinning temperature, cooling condition. winding overfeed ratio and oil content. on the process of POY is investigated. 本文主要对原料切片质量，干燥切片含水率．纺丝温度和冷却条件．组件组装工艺，卷绕超喂率及上油浓度等影响因汞作了初步的探讨。
- A bowl of hot chicken soup is good for you. 喝一碗热鸡汤对你有好处。
- The hot weather has soured the milk. 炎热的天气使牛奶变酸了。
- In this article, the design of "-"spinneret of Polyester FDY was introduced.The effect of spinning temperature , spinning speed and quench process to the flat target of the filament were discussed. 介绍了涤纶FDY扁平丝“-”型喷丝板的工艺设计,主要讨论了纺丝温度、纺丝速度、侧吹风等工艺对纤维扁平度指标影响。
- The Hot Spinning of Head Plates'Forming and Application 封头的热旋压加工及应用
- Bright chips subjected to superdrawing generated high|strength yarn at properly elevated spinning temperatures and drawing temperatures in the presence of proper finishes. 适当控制纺丝温度及拉伸温度 ,并选择适当的油剂 ,大有光切片可经纺丝超倍拉伸制得高强丝。
- The temperature has stayed hot this week. 本周气温一直都很热。
