您要查找的是不是：
- hook forging die 吊钩锻模
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通过对吊钩的工艺分析，设计了合理的锻造工艺方案及其热锻模，并对出现的缺陷进行了分析解决。
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式热锻模具的设计
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 给出了震动器机壳斜销式液锻模具设计结构。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介绍了几种典型模具快速修复工艺方法,并对汽车地板革成形模和汽车半轴摆动辗压模的修复进行了研究。
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用动态光弹性法研究了锤锻模燕尾的动态应力集中问题。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要传统锻模加工，由于加工道次多，且需采用放电加工制造模穴，导致有制造时间长，且成本偏高的缺点。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 简要地介绍了镶块锻模结构特点和可塑性优化设计的难点;着重介绍扩大其使用性能可塑性设计方法的要点.
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13钢连杆锻模的寿命问题,讨论了模具寿命与模具硬度的关系,提出了提高模具寿命的措施,设计了H13钢连杆锻模的最佳热处理工艺。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通过对轿车左右横臂的结构及锻造工艺分析,制定了其模锻工艺流程,介绍了模锻工艺及其工步型腔设计。
- By improving the design of forging die and using press-forging and backward extrusion principle,solves the problems of 130 steering knuckle forming which can not be fully filled during forming. 通过改进预锻模膛的设计,利用镦粗成型、反挤成型的原理,有效解决了130转向节板部模锻成型时充不满的问题。
- Because of the forming temperatures are different, the cooling of warm molding forging are distinguish from hot forging forming.The cooling method and design of warm forging die are introduced. 因其成形温度的特点,对温锻模具冷却有别于热锻成形。
- The teacher let him off the hook with a warning this time. 这一次老师放过他，只给了一个警告。
- So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此，连杆锤锻模ICAD系统的研究就有了重要的意义。
- BOLT &NUT FORMING DIES,TUNGSTEN CARBIDE DIES,PRESSING DIES,FORGING DIES,PUNCHES,K.O.PIN.ALLOYSTEEL,TOOLINGS. 各种螺丝、螺帽冲压成型模具、碳化钨冲压模具、合金钢工具、模具、零件冲压、锻造模具。
- The boxer let his opponent off the hook many times. 那拳击手失掉了许多次击败对手的机会。
- See if you can hook it with this pole. 看看能不能用这根杆子把它捞起来。
- A lever pattern of the ejetion mechanism was designed to solve the problem of the hot chain element being taken out from the air hammar forging dies. 针对链节胎模锻存在起模困难的问题,设计了一套杠杆式顶出机构顶出制件,采用此机构可提高生产率,同时,减少了热锻件的闷模时间,提高模具的使用寿命。
- These two pieces of the chain hook together. 这两个链环套在一起。
