您要查找的是不是:
- heavy interference fit 重型过盈配合
- Due to heavy interference(static) Contact Kun Ming with difficulty. 因严重干扰(灭电干扰)与昆明联系困难。你被打断,请再讲一次。
- Bearings with a tapered bore are always mounted with an interference fit. 带圆锥孔轴承始终以过盈配合安装。
- FEM stress analysis of assemble symmetrical body of interference fit. 过盈配合组合轴对称体有限元法应力分析
- Therefore, the ring need not necessarily have an interference fit unless this is required for other reasons. 因此,轴承圈不一定要有过盈配合,除非因其它原因需要这样做。
- For bearings having a tapered bore, inner rings are always mounted with an interference fit. 对于圆锥孔轴承,内圈的安装始终采用过盈配合。
- Alignment needle roller bearings should have an interference fit in the housing bore. 对中滚针轴承的轴承座孔应过盈配合。
- The bearings are generally mounted with an interference fit on the roll necks and therefore often have a tapered bore. 轴承一般以过盈配合安装在轧辊轴颈上,因此经常带锥形孔。
- Research on interference fit riveting, composites structure riveting and driving interference-fit fastener have been done. 对电磁铆接技术在干涉配合铆接、复合材料结构铆接、干涉配合紧固件安装方面的应用进行了系统研究。
- With this control algorithm, it is not necessary to know the precise model of the controlled objects, and good performance can be achieved even with heavy interference. 采用本文控制算法,不需要有精确的被控对象模型,即使在有较大干扰的情况下,仍可以获得较好的控制性能。
- But the interference fit by hydroform result in the damage occurring on the contact surface. 然而,由于锥套与辊颈利用液压胀形实现过盈装配,使得接触面间在装配过程中发生表面损伤。
- The interference fit between the gate and seats provides bubble tight shutoff, even under the lowest pressure. 即使在最低压力条件下,闸板和阀座之间的交互界面也能够实现气密性关闭。
- The interference fit between the gate and seat provides bubble tight shutoff even under the lowest pressure. 即使在最低的管线压力下,闸板与阀座之间的配合也能够实现气泡级密封功能。
- Forced to compensate for the heavy interference in this band, wireless LANs can support only 1Mto 2M bit/sec throughput.These data speeds can limit the types of business applications wireless LANs can support. 迫于弥补此频段上的严重干扰,无线局域网仅支持1兆至2兆位/秒的吞吐量,这种数据传输速度限制了无线局域网所能支持的商业应用领域。
- Bearings with a tapered bore are used when an interference fit is required for the inner rings on the roll neck, e. G. When rolling speeds are high. 在轧辊轴颈上的内圈需要过盈配合时,例如轧钢速度高时,使用带锥形孔的轴承。
- Forced to compensate for the heavy interference in this band,wireless LANs can support only 1Mto 2M bit/sec throughput.These data speeds can limit the types of business applications wireless LANs can support. 迫于弥补此频段上的严重干扰,无线局域网仅支持1兆至2兆位/秒的吞吐量,这种数据传输速度限制了无线局域网所能支持的商业应用领域。
- Interference fit is required between outer ring and housing as the load is varying in direction relative to the outer ring. 外圈与轴承座之间需要过盈配合,因为相对于外圈的负荷方向有变化。
- The process problems of composite structures using interference fit technology can be solved by use of Stress Wave Riveting (SWR). 分析了复合材料结构采用干涉配合技术存在的工艺困难,利用应力波铆接设备对碳纤维复合材料进行了干涉配合铆接试验,并对铆接质量进行了检测分析。
- The locknut torque needed to move the washer at the maximum washer interference fit shall not exceed the torques given in Table 3. 锁紧螺母扭矩压紧垫片时,其与垫片的最大相互作用力不能超过表3所给扭矩值。
- To dismount a bearing having an interference fit, the tools described in the following section may be used, the choice of tools will depend on bearing type, size and fit. 拆卸过盈配合的轴承,可使用下述各种工具,而工具的选择取决于轴承类型、大小和配合。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries