您要查找的是不是:
- hand wheel screw down 手轮压下装置
- Screw out the oil plug while filling, and screw down as finished. 注油时,将油塞旋下,注油毕,再将油塞旋上拧紧。
- Select a hand wheel or a hinged presser food to sew the stuff. 选用轮线或平押脚,来车缝纫物品。
- When the hand wheel rotation through the stem hole lead plane in the middle of the plunger up and down reciprocating movement to complete the valve to open and close the function. 当手轮旋转,通过阀杆带动柱塞在孔架中间上下往复运动来完成阀门的开启与关闭功能。
- The blackboard was screwed down to the wall. 黑板是用螺丝拧在墙上的。
- Hand wheel,lever and spanner driving and safety valve,pressure reducing valve,traps overleap this symbol. 注:1、手轮、手柄和扳手传动以及安全阀、减压阀、疏水阀省略本代号。
- The beam was screwed down to the cross bar. 横梁已用螺丝柠在垮木上。
- A usually thin nut screwed down on another nut to prevent it from loosening. 防松螺母常指拧紧在另一个螺母上的防止其松动的细螺母
- I am screwed down by fixed rules. 我被清规戒律束缚住了。
- Clearance between shearing blades adjusted by hand wheel to be quicq, accurate and convenient. 刀片间隙由手动轮调整,迅速、准确、方便。
- Valve CLOSE when turn hand wheel clockwise and OPEN when turn hand wheel counterclockwise as usually custom. 本装置手轮顺时针旋转阀门关闭,逆时针旋转阀门开,与一般习惯相同。
- This paper introduces the screw down coned system on the 2800mm plate mill of Anyang Iron and steel company. 综述了厚板轧机的发展及其技术改造的特点;
- Each hand wheel shall be fitted with a circular nameplate which is in English language on Stainless steel material, indicating the valve number. 每个手轮(操作盘/驾驶盘)的不锈钢部分须帖有相对应的英文铭牌;注明阀门号(这个就不太懂;不知道是什么阀门号码).
- The coffin lid had been screwed down. 棺材盖已经盖紧了。
- Squeaking floorboards should be screwed down. 踏上去咯咯作响的地板应用螺钉钉住。
- When opening, the hand wheel will give an initial resistance, then suddenly turnabout 1 /2 turn with little resistance. 开启的时候,手轮会引起一个最初的阻力,接着在这个小阻力下突然旋转大约1/2圈。
- Swivelling operating panel with colour monitor and electronic manual control device, with electronic hand wheel. 回转操作板,带彩色监控、电子手动控制装置、电子手轮。
- The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt. 本阀可水平或垂直安装,安装时两法兰连接中间必须加密封垫片,然后均匀锁紧螺栓。
- Loosen locknut and draw out the handle to open random position when operate.Then screw down locknut to make the disc settled in this position. 运行时先松开锁紧螺钉,手握把手向外抽出,达到工况开启任意位置,然后拧紧锁紧螺钉,使插板停留在这一位置。
- Conduct maintenance on the equipment and grease the threaded rod and hand wheel nut periodically(every one year or half year). 定期(一年或六个月)对设备进行一次保养,丝杆及手轮螺母部分上油。