您要查找的是不是：
- hand molding press 手工模压机
- We are planing to make a hand mold by hand at first, it needs one week. Once it is completed, i will sent it to you. 我们准备先用手做一个手工模型;需要一个星期时间.;手工模型几乎完全和你们的样品一样;一旦你们确定模型没有问题;我们再正式开模具
- And the effect of different molding press and different annealing system on the properties of foam glass was analyzed. 讨论分析了成型压力和退火制度等工艺过程对泡沫玻璃性能的影响。
- Putting hat on the lower mold and pushing the button , the lower mold uphold hat with steam and the upper mold press down crown and brim at the same time. 在下模具上放置帽子，按动开关，上模具下降，中模具上升，并同时喷射蒸汽，同时整烫。
- The results of the water-surrounding rubbing wear experiments on the ZrO2 ceramics with various molding press indicate that the compact with a molding press of 150 MPa possesses a low wear rate and a favorable abrasive wear resistance. 对不同成型压力条件下的ZrO_2 陶瓷进行了水环境下的摩擦磨损试验,结果表明本试验条件下ZrO_2 陶瓷磨损机理为沙粒冲击形成的裂纹经扩展形成凹坑,使试样受到磨损,150MPa 压力下ZrO_2 陶瓷具有较低的磨损率,抗摩擦磨损能力好。
- We can produce more than 10 varieties of products in 6 categories, including knurling, relievo, printing, spraying, vertical mold pressing, etc. 生产滚花、浮雕、印刷、喷涂、立体模压等六大类十几个品种。
- We are producer of Bag Gloves all kinds . The Glove in picture Made of Buffalo leather , Hand molded inside rubber+underlay+foam . 我们生产的袋式手套各种。手套的图片制作水牛皮革，手工成型橡胶内背后的泡沫。
- The polymethylsiloxane(PDMS) mixers used in optical evaluation were fabricated by mold pressing. 利用模压工艺制作出适于光学探测的聚二甲基硅氧烷（PDMS）混合器。
- Flatten the dough with a press of the hand. 用手把生面团压平。
- rotary compression molding press 旋转式压缩成型机
- The aerofoil rib parts for pilotless aircraft was manufactured by using mold pressing process with epoxy resin as matrix materials and glass cloth as enhancement materials. 以环氧树脂为基体,以玻璃布和碳布为增强材料,采用模压成型工艺制备了某型无人机机翼环肋复合材料结构件。
- The poems were printed on a small hand press. 这些诗是在一台小型手动印刷机上印的。
- It's made of bronze or iron powder, mold pressed in high pressure, sintered in high temperature and soaked in oil by vacuum. 该产品于是以铜粉或铁粉为原料，经模具压制、高温烧结、真空浸油后加工而成。
- His sooty hand smudged the paper. 他被煤烟熏污的手把纸弄脏了。
- A tough, but low abrasion carbon fiber packing impregnated with PTFE and twined through advanced twining techniqure of wick-penetrating, then carbonized or mold pressed. 以特殊工艺的碳纤维为骨架，以耐腐蚀性极强的PTFE为基材，采用国内最先进的穿芯式编织法，编织成致密结构织物，经碳化、烧结、模压制成的各种形式的密封环。
- Short carbon fiber reinforced pitch-based carbon/carbon composites (SCFRC) with high density and low cost were fabricated by mold pressing followed by semi-carbonization. 摘要利用模压半炭化成型工艺在大气环境下制备出了短切炭纤维增强沥青基C/C复合材料（简称SCFRC）。
- PVDF/graphite conductive composite bipolar plate were prepared by mold pressing in high temperature.Electrical conductivity, flexural strength and gas permeability were measured. 摘要采用聚偏氟乙烯(PVDF)与导电填料石墨复合，通过高温模压方法制备了导电复合材料双极板，测量了双极板的电导率、弯曲强度和气密性。
- The children walk down the street hand in hand. 孩子们手拉手地在街上散步。
- The teacher asked the pupil to put his hand down. 老师叫这个小学生把手放下。
- She picked up a new magazine with her free hand. 她用空着的一只手拿起一本新杂志。
