您要查找的是不是：
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用动态光弹性法研究了锤锻模燕尾的动态应力集中问题。
- So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此，连杆锤锻模ICAD系统的研究就有了重要的意义。
- Optimization expert system of hammer forging die materials 锤锻模具材料优化专家系统
- Study on 3D CAD System of Hammer Forging Die for Carriage Forging 客车锻件锤锻模三维CAD系统的研制
- PHOTOELASTIC STUDY OF DYNAMIC STRESS CONCENTRATION AT SWALLOWTAIL ON HAMMER FORGING DIE 锤锻模燕尾动态应力集中的光弹性研究
- Development of the 3D CAD System for the Hammer Forging Die for the Forged Parts of Buses 客车常用锻件锤锻模三维CAD系统的研制
- 2.So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此，连杆锤锻模ICAD系统的研究就有了重要的意义。
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式热锻模具的设计
- The hammer forging process of TC6 titanium alloy clasp has been simulated by using rigid-viscoplastic FEM. 在TC6钛合金卡环的高温锤锻过程中,模具承受非常大的应力。
- Design, construction and using of a gas heating furnace for hammer forging have been introduced. 介绍了一台锻锤用煤气加热炉的设计、施工及使用情况。
- Die blocks for closed-die hammer forging 锻锤用模具坯料
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 给出了震动器机壳斜销式液锻模具设计结构。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通过对吊钩的工艺分析，设计了合理的锻造工艺方案及其热锻模，并对出现的缺陷进行了分析解决。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介绍了几种典型模具快速修复工艺方法,并对汽车地板革成形模和汽车半轴摆动辗压模的修复进行了研究。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要传统锻模加工，由于加工道次多，且需采用放电加工制造模穴，导致有制造时间长，且成本偏高的缺点。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 简要地介绍了镶块锻模结构特点和可塑性优化设计的难点;着重介绍扩大其使用性能可塑性设计方法的要点.
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13钢连杆锻模的寿命问题,讨论了模具寿命与模具硬度的关系,提出了提高模具寿命的措施,设计了H13钢连杆锻模的最佳热处理工艺。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通过对轿车左右横臂的结构及锻造工艺分析,制定了其模锻工艺流程,介绍了模锻工艺及其工步型腔设计。
- CAD of finishing cavity for hammer forging 锤上模锻终锻型槽的计算机辅助设计
