您要查找的是不是：
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介绍了几种典型模具快速修复工艺方法,并对汽车地板革成形模和汽车半轴摆动辗压模的修复进行了研究。
- half-axle swing forging die 半轴摆动辗压模
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式热锻模具的设计
- Design of New Die for Precision Forging of Half Axle Gear of Automobile Differential 汽车差速器半轴齿轮新型锻模设计
- Keywords motorized gear;differential gear;half axle gear;precision die forging;gear precision forging; 汽车齿轮;差速器齿轮;半轴齿轮;精密模锻;齿轮精锻;
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 给出了震动器机壳斜销式液锻模具设计结构。
- Keywords Half axle;Obturated cold forging;Residual stress;Grain size; 半轴齿轮;闭塞冷锻;残余应力;晶粒度;
- This paper demonstrates residual stress of induction quench parts and personal views about stress distribution of flange corner heat treatment ,truck half axle material and depth of hardened layer. 论述了感应淬火零件的残余应力形态,并对载货车半轴的材料、硬化层深度及法兰圆角淬火层分布提出了个人见解。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通过对吊钩的工艺分析，设计了合理的锻造工艺方案及其热锻模，并对出现的缺陷进行了分析解决。
- This paper presents a model for half axle gear fixture design based on the environment of concurrent product development ,together with detailed introduction of its realization method . 提出基于并行产品开发环境的半轴齿轮夹具设计的系统结构模型,并且对该结构模型的实现方法作出了详尽的阐述。
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用动态光弹性法研究了锤锻模燕尾的动态应力集中问题。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要传统锻模加工，由于加工道次多，且需采用放电加工制造模穴，导致有制造时间长，且成本偏高的缺点。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 简要地介绍了镶块锻模结构特点和可塑性优化设计的难点;着重介绍扩大其使用性能可塑性设计方法的要点.
- Failure Analysis of Automobile Half Axle 汽车半轴失效分析
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13钢连杆锻模的寿命问题,讨论了模具寿命与模具硬度的关系,提出了提高模具寿命的措施,设计了H13钢连杆锻模的最佳热处理工艺。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通过对轿车左右横臂的结构及锻造工艺分析,制定了其模锻工艺流程,介绍了模锻工艺及其工步型腔设计。
- Die Design for the Cold Extrusion Test of the Half Axle Spline of Minicars 微车半轴花键冷挤压实验模具设计
- So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此，连杆锤锻模ICAD系统的研究就有了重要的意义。
- BOLT &NUT FORMING DIES,TUNGSTEN CARBIDE DIES,PRESSING DIES,FORGING DIES,PUNCHES,K.O.PIN.ALLOYSTEEL,TOOLINGS. 各种螺丝、螺帽冲压成型模具、碳化钨冲压模具、合金钢工具、模具、零件冲压、锻造模具。
