您要查找的是不是：
- gnatho guide plate 颌导板
- Install guide plate and adjuster cable on anchor pin. 将导向板和调整器钢缆安装到锚销上。
- The vaporize, condense, overflow and guide plate inner are made in stainless steel. 蒸发锅、冷凝管、溢流坝和内部导流板都用不锈钢制成。
- The steam produced in vaporize pan reached the condense pipe through guide plate. 在蒸发锅中发生的蒸汽经过导流板装置到达冷凝管。
- The guide plate be installed as can change direction three times before the steam enters the condense pipe. 导流板被安装成为能使蒸汽进入冷凝管之前改变方向三次。
- With the car upside-down, the ball forces the plunger to seat against the guide plate. 当汽车倾倒时，滚珠迫使柱塞落在支承板上。
- And the cover outside and the cover of guide plate are made in heat-resistant borosilicate glass, all the electric elements with safety cut off switch. 外部盖子和内部导流板的帽子都用耐高温硼硅酸盐玻璃制成，所有电器元件都安装上保护切断。
- Its application situation on heat shearing blade,guide plate and nodular indefinite chill roll are introduced too. 并阐述了这种焊条在热剪剪刃、轧机导板头、球墨无限冷硬铸铁轧辊堆焊等方面的应用情况。
- The new light guide plate is made of methylmethacrylate and micro-prism structures are embedded on its lower surface. 新设计是以压克力为导光板的材质并且在导光板的底面置入微菱镜结构，藉此取代反射片及菱镜片以减少背光模组的厚度。
- It is analysed that driving the whee land chain of BH29 chain Saw are weared and teared, which affects Saw chain and guide plate. 分析BH29油锯的驱动链轮受力磨损情况,及对锯链、导板的影响。
- This paper discussed the new technologies of light guide plate in backlight system, and made an expectation about the future of light guide plate. 文章就目前新型导光板技术进行了讨论，并对未来导光板的发展方向做出展望。
- The disadvantages of the conventional light guide plate (LGP) such as complicated structure and high cost are widely concerned nowadays. 摘要传统背光系统结构复杂，成本高等问题越来越引起广泛关注。
- Light guide plate (LGP) is a key component of lower cost and easier self-development in LCD backlight module (BLM) with small size. 目前小尺寸背光模组的设计中，导光板是成本较低且易自行开发的关键零组件。
- Y.Y. Lin, T.L. Wang and Y.T. Huang, Design of Light Guide Plate with Inverse Prism Microstructure, OPT2008 conference in Taiwan. 王韬霖、黄耀宗，双侧边式入光导光板出光光场调整研究，2008年中国材料年会论文集。
- This work investigates the irradiance uniformity of backlight units(BLU) as different microstructures(dot radius) were put on their light guide plate(LGP). 摘要:本研究主要探讨背光模组中导光板底面网点的排列分布对发光面均匀度的影响。
- Methods:11 children were selected, alignment anterior teeth by using the fixed appliances, after making lower jaw protrusive movement by using the inclined guide plate. 方法:选择11名儿童患者,先用固定矫正器排齐上下前牙,再用斜面导板导下颌向前。
- The role of the light guide plate (LGP) of a backlight module is to guide the light source to reach both high luminance and high luminance uniformity purposes. 背光模块中导光板的作用在于引导光的方向，用来提高面板的辉度，确保面板辉度的均匀性。
- Methods: 11 children were selected, alignment anterior teeth by using the fixed appliances, after making lower jaw protrusive movement by using the inclined guide plate. 方法：选择11名儿童患者，先用固定矫正器排齐上下前牙，再用斜面导板导下颌向前。
- The results of full factorial experiment are show that the radius of dot pattern increasing induces the brightness in front of light guide plate increasing. 最后，利用全因素实验得知导光板前方之辉度值会随著网点半径的增加而增加；
- Make sure that the film stays within the film guides, and that the upper sprocket edge is under the guide plate. 要保证胶片嵌入胶片槽,且上齿边缘在槽板下。
