您要查找的是不是:
- geometrical parameter method 几何参数法
- This paper deals with a kind of analytic method which is applied to determine the geometrical parameter of faults,to get formula of dip direction azimuth of line of intersecting plane of faults and dip angle of fault plane. 为此,本文系统介绍确定断层几何参数的解析方法,并给出能够单值求出断层交面线倾向方位角和断层角的公式。
- The method is thus named the parameter method for large pore paths,whi... 结果表明:大孔道参数法识别大孔道是行之有效的。
- The groove is optimized, reconstructed and validated by means of the influence of geometrical parameter and the optimized parameter choice. 分析了刀具几何参数的影响并优化了参数选择,在此基础上,做了槽型优化和重构,并进行了验证。
- A method for the optimization of the drawbead geometrical parameters was built , which was based on the response surface method and genetic algorithm. 引入响应面方法和遗传算法建立基于近似模型的拉延筋几何参数反求方法。
- The groove is optimized,reconstructed and validated by means of the influence of geometrical parameter and the optimized parameter choice. 分析了刀具几何参数的影响并优化了参数选择,在此基础上,做了槽型优化和重构,并进行了验证。
- The Selection of blades type and the design of blade geometrical parameter will directly effect the working quality and energy consumption of cultivator. 刀片的形状选择及其几何参数的设计将直接影响到耕耘机的作业质量和能量消耗。
- The stable cavity condition is obtained by ABCD law and equivalent G parameter method. 利用abcd传输矩阵理论及等效G参数法计算了稳腔范围。
- This study proposes a new mix design method for self-compacting concrete(SCC) named parameter method. 提出一套计算自密实混凝土配合比的参数设计法。
- The parameter method is comparatively useful in the cost estimation of new type weapon system. 参数法是较为有用的新型武器系统制造成本估算方法。
- The method and procedure of measuring and calculating involute spur gear geometrical parameters such as tip diameter, module, modification coefficient and pressure angle were shown in this paper. 本文阐述了渐开线直齿圆柱齿轮顶圆直径及齿轮模数、变位系数和压力角等参数的确定方法和步骤.
- A thermal network model of the wet back driving axle of ZL80 wheel loader steady heat transfer was built by lumped parameter method. 摘要采用集总参数法建立了ZL80型轮式装载机湿式后驱动桥的稳态传热网络模型;
- An optimum design system consisting of geometrical parameter design, strength calculation,life estimation and optimum design program odule for curve-tooth hypoid gear is developed. 开发了由几何设计、强度计算、寿命估算和优化设计程序模块组成的弧齿准双曲面齿轮优化选型设计系统。
- We have determined tin and lead contents in tin solder using the XRF fundamental parameter method without standard sample in this paper. 本文在无标样的情况下,用X射线荧光基本参数法测定了焊锡中的锡和铅的含量。
- Conclusions: The modeling can be used to the clinical practice for exploring the intrinsical relationship between the bone geometrical parameter and the biomechanical attributes at the pelvic and hip. 所建立的人体髋关节生物力学普适模型,可有效地应用于临床髋关节生物力学分析,从而为揭示骨盆骨性几何参数与髋关节接触力与应力分布间的本质关系、为临床治疗髋关节疾病等提供科学的理论依据。
- A dynamic heat transfer model based on the lumped parameter method was developed for cooling system of vehicle internal combustion engine. 提出了一个基于集总参数+法的车用内燃机冷却系统动态传热模型。
- A large number of geometrical parameters influence these coefficients, and range of design configuration is wide. 有许多几何参数影响这些系数,且设计外型变化很大。
- The oil tanker heat preservation model is established and the software is developed based on transient heat conduction gathered parameter method. 根据非稳态导热集总参数法建立油船油舱保温数学模型,研制了油船货油保温计算软件。
- Finally, compute the geometrical parameters of deformed grids and strain contribution on the piecework surface. 最后,由特征点的空间坐标,计算出各圆的几何参数和应变,得到工件表面的应变分布。
- In ray techniques based on GO and GTD,the radii of the curvatures of the reflec-tors and reflected wavefronts are important geometrical parameters. 在基于GO和GTD的射线法中,镜面和反射波面的曲率半径是重要的几何参数。