您要查找的是不是：
- A constitutive model of unsaturated intact loess was obtained by the generalizing shear stress dividing by the structural parameter increasing monotonously with shear strain. 试验揭示了湿陷性黄土具有剪缩剪胀性，表明应力比与剪缩剪胀应变比之间具有良好的线性关系；
- generalized shear strain 广义剪应变
- The shear strain can be determined in the following way. 用下列方法能够确定切应变。
- Shear strain in MBE grown CdTe films on Si(211) substrates[J]. 引用该论文 王元樟;陈路;巫艳;吴俊;于梅芳;方维政;何力.
- The transformation is due to the shear strain imposed on the specimen by ECAP. 该转变发生是由于ECAP过程中材料承受剪切应变,应变能累积诱发再结晶,从而形成等轴晶双相结构。
- A double trapezoidal specimen will generate shear debonding. 双梯形的试样将产生切变脱胶现象。
- The only strain is a shear strain and the dilatation is zero, these waves are called shear waves. 唯一的应变是剪应变而没有膨胀，这种波叫剪切波。
- Good bonds are always accompanied by surface extension, that is, plastic shear strain. 良好的键合总伴有表面延伸即塑性切向形变。
- Variation of Damping Properties Under Magnetic Field and Shear Strain Amplitude in Fe-Cr-Al Alloys. 高阻尼Fe-Cr-Al合金在磁场和应力场下的阻尼行为
- The elasticity of copolyester increases with the shear strain but decreases with the temperature. 弹性随切应力的增大而增大,随温度的升高而降低。
- The residual strain is the additional shear strain created with the increase of pore pressure due to cyclic shear under initial shear stress. 残余应变是由于周期剪切引起孔隙压力增长;在初始剪力作用下产生的附加的剪应变.
- The results show that the data of shear strain 2 are reliable because the component 2 and 4 of shear strainmeter work normally. 通过对标定系数和滞后时间的分析认为：元件2、4工作状况比较稳定，观测值差应变2是比较可靠的；
- Moreover, high value region of maximum shear strain and superficial expansion in this area is in Tianjing, Beijing, Tangshan area. 区内最大剪应变、面膨胀的高值区在天津、北京、唐山一带。
- Showed that by a special choice of initial axes, the mathematical impact of shear strain rate is removed, and only dialation and rigid rotation remain. 藉由选择特殊的起始轴，显示当去掉剪切应变速率，仅保留扭曲和刚性旋转的数学上的影响。
- Non-uniform shear dilatancy of rock specimen due to plastic shear strain localization is analyzed considering strain gradient effect. 摘要采用梯度塑性理论，对岩样剪应变局部化引起的扩容进行了理论分析。
- Furthermore,a new simplified elastic method called as inherent shear strain method is developed for forecasting fillet weld's angular distortion. 在此基础上,进一步提出了一种用于预测角焊缝角变形的线弹性简化方法,即剪切固有应变法。
- Derived results are able to reflect the influence of the quality of a material to them,compared with the result from the shear strain energy strength theory. 导出的结果与由剪切应变能强度理论得来的结果相比,能够反映材质的不同对疲劳极限条件的影响。
- Objective. To investigate intradiscal pressure, shear strain between anulus and adjacent endplates, and fiber strain in the anulus under pure and combined moments. 目标：调查在环与相邻终板之间的盘内压和切应力，以及单纯和联合运动时的纤维强度。
- Natural deformational zones are commonly the result of general shear, a combination of pure shear (coaxial contraction or extension) and simple shear. 天然变形带通常是一般剪切作用的产物，是纯剪切(共轴缩短或伸展)和简单剪切的组合。
- Objectie. To inestigate intradiscal pressure, shear strain between anulus and adjacent endplates, and fiber strain in the anulus under pure and combined moments. 目标：调查在环与相邻终板之间的盘内压和切应力，以及单纯和联合运动时的纤维强度。
