您要查找的是不是:
- gear reduction ratio 齿轮减速比
- steering gear reduction ratio 转向齿轮机构降速比
- High reduction ratio during primary and secondary crushing stage. 初段,二段等各段破碎均有大破碎比。
- Using lumped mass model, we construct dynamic equation of the flexible arm as well as its Simulink model. Using Simulink model, we analyze how Coulomb friction, motor inertia and reduction ratio of gear affect system performance. 采用集中质量模型建立了柔性手臂的动力学方程及其Simulink模型,利用Simulink模型仿真分析了库仑摩擦力、电机转子惯量和齿轮减速比对系统性能的影响。
- The midheaven axis gear reduction electrically operated actuation,does not need to refuel the province space. 中空轴型齿轮减速电动驱动,无需加油省空间。
- Gear reduction system may consider to be pinion transmition in stead of planetary system to saving spacing . 为节省空间起见,降齿系统可以考虑采用小齿传动,而不用星系系统。
- They will vary by catalog number and style, for example Nippon Denso Gear Reduction unit minimum measurement is 1.2mm (.047”). 它们会随着星表数目和式样的变化而变化。如NipponDenso齿轮缩小型部件的最小值是1.;2mm
- NIBCO electric actuators operate on the gear reduction motor principle, which allows opening and closing speeds ranging from two seconds to one minute or longer. 美国尼伯科电动执行机构采用齿轮减速电机原理,因此开启和关闭速度控制在两秒至一分多钟范围内。
- The inspiratory expiratory value difference (VD) and area reduction ratio (AR) of bilateral lungs were calculated. 结果各年龄组内男女之间的VD和AR无显著性差异;
- Because there are different ways to build a gear reduction unit, eg chain and sprocket or gearbox, we are only showing you the setup angle of the muller. 由于有不同的方法来建立一个齿轮减速装置,如链及链轮或变速箱,我们只显示您的马勒设置的角度。
- Through the comparison of numerical simulation value and experiment results, the range of reduction ratio was obtained while the tube forming ideality. 通过数值模拟与实验结果的比较,得出了获得较理想的成形薄壁筒形件时减薄率的选取范围。
- It is found that the tensile strength and the hardness of the specimen decrease, while the elongation and the reduction ratio of area increase. 在平行试样方向上施加强磁场进行退火处理后,球铁的拉伸强度、硬度降低,延伸率、断面收缩率升高。
- The uneven distribution of the reduction ratio of Mo square bar swaged into the circular bar and the Practice calculation method of reduction ratio were discussed. 讨论了钼方坯旋锻归圆前压缩比的不均匀分布情况及其实际压缩比的计算方法。
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stock completely by hot rolling reduction ratio, macroetching testing and SEM. 摘要一些亚包晶合金钢连铸大方坯出现低倍星状裂纹,在一定的压缩比下经轧制仍不能完全消除这种低倍缺陷。
- Vertical type gear reduction motor 产品描述:立式减速马达
- At last, new failure thickness reduction ratio criterion is used to determine the forming limit of St14 steel based on the numerical system, and the prediction are compared with experimental FLD. 最后,在数值模拟中应用不同形式和参数组合的厚度减薄率判据进行成形极限图预测,并与实验结果进行了比较。
- Horizontal type gear reduction motor 产品描述:卧式减速马达
- The star cracks in macrostructure appear in some hypo-peritectic continuous cast alloy blooms and these cracks cannot be stuck completely by hot rolling reduction ratio,macroetching testing and SEM. 一些亚包晶合金钢连铸大方坯出现低倍星状裂纹,在一定的压缩比下经轧制仍不能完全消除这种低倍缺陷。
- The driven gear fits its driving gear like a glove. 这个从动齿轮与它的主动轮啮合得非常好。
- My whole morning's work has been put out of gear by that mishap. 我一个上午的工作全让这倒霉的事给弄得乱了套。