您要查找的是不是：
- gear teeth number 齿轮齿数
- To cause(gear teeth) to become engaged. 使（齿轮）相啮合
- Spray or paint grease onto the gear teeth. 将油酯喷或涂到齿轮齿条上。
- The parameters calculation method of groove for hot rolled ribbed bars, such as the gap of end of cross rib, the teeth number of change gear, etc. 介绍了在热轧带肋钢筋轧槽加工中，横肋末端间隙、挂轮齿数等参数的计算方法，和实际应用经验，及其与负偏差轧制的关系。
- Exact modeling of gear teeth is based on meshing theory. 摘要根据齿轮啮合原理，建立了轮齿的精确齿形。
- This paper advanced a practical and succinct formula for tooth number choice of involute gear. 从等强度概念出发,推出一个据以选取渐开线齿轮齿数的简单、实用公式。
- Check ring gear and pinion gear teeth contact pattern. 检查环形齿轮齿接触印痕。
- Inquires into the EHL calculation for involutes planetary gear drive with small tooth number difference and its relative formulas are derived. 从受力分析、承载能力、平衡减振、传动效率和系列设计等方面,对少齿差环板式减速器的研究现状进行了评述。
- Gear teeth in mesh. 相互啮合的齿轮
- Accordingly,the least teeth number without undercutting is also decided only by the design pressure angle of the gear,without any relation to the coefficient of addendum height of the gear. 相应的无根切最少齿数也仅取决于正弦齿轮的设计压力角;而与齿顶高系数值无关.
- The engagement of gear teeth. 啮合齿轮的互相咬合
- Using Zr41.25Ti13.75Ni10Cu12.5Be22.5 bulk metallic glass rods of 5 mm diameter, fine spur gear with boss (pitch diameter 6 mm, number of gear teeth 24, modulus 0.25 mm) is fabricated with super-plastic die-forging method under vacuum condition. 以直径为5 mm的zr41.;25Ti13
- In this paper, using Zr41.25Ti13.75Ni10Cu12.5Be22.5 bulk metallic glass rods of 5 mm diameter, fine spur gear with boss (pitch diameter 6 mm, number of gear teeth 24, modulus 0.25 mm) is fabricated with super-plastic die-forging method. 本文以直径为5 mm的Zr41.;25
- The distance between two corresponding points on adjacent screw threads or gear teeth. 螺距两个相对应的点或相邻的螺钉之间的距离
- If possible ,use the same lubricant for the raceway system and the gear teeth as used for initial operation. 如可能，使用与第一次润滑相同的润滑剂来润滑轴承座圈和齿轮齿条。
- The test of Pb samples indicates that the die set works smoothly and gear teeth are filled fully. 根据铅试样模拟实验表明,模具装置工作顺畅,齿轮成形饱满。
- It should be said GALLUS machine meshing gear teeth, there was a small staves of opportunities. 不该说GALLUS的机械是歪齿轮啮合的，呈现齿杠的时机小。
- The gear teeth and meshing line are distorted in the meshing process as a result of wearing and rise in temperature. 实际应用中，由于磨损和受热等原因，使得齿轮齿廓以及啮合过程中啮合线都发生了畸变。
- When change gear could not be mated for too big ratio of differential change gear,to select suitable teeth number increament to finish hobbing of big prime number helical and straight-toothed gears. 滚削大质数斜齿及直齿齿轮,若因差动挂轮比值过大或过小,而不当搭配挂轮时,可以通过选择适当的齿数增量来解决问题。
- Milling can produce flat or angled surfaces, groves, slots, gear teeth, and other profiles, depending on the shape of the cutters being used. 铣削可根据所用的铣刀形状分别加工平面或斜面、槽口、缝、齿轮齿及其它型面。
