您要查找的是不是:
- gear shaft roller bearing 齿轮轴滚柱轴承
- It is studied the existing three kinds of bearing arrangement for the driving gear shaft of locomotive motor. 摘要研究了现有的3种机车电机主动齿轮轴轴承布置方式。
- Self aligning double row spherical roller bearing allows for a higher degree of angular deflection of the drive shaft. 自对正式双列球面滚动轴承允许驱动轴有更高的偏转角度。
- Thrust needle roller bearing is a bearing. 推力滚针轴承是轴承的一种。
- Entity-type needle roller bearing is a bearing. 实体型滚针轴承是轴承的一种。
- Needle roller bearing is a bearing. 滚针轴承是轴承的一种。
- The central and beam shaft block adopts middle width roller bearing which has the ability of good sealability, strong endurance. 中央轴承座和横梁轴承座的轴承选用中宽系列滚子轴承,密封性好、承受能力强;
- The paper analyzed the deflection of a compound planetary gear set and calculated the damage percentage of its roller bearing. 针对某行星变速机构复合排行星齿轮和滚针轴承进行了受力变形分析和损伤率计算。
- RUGGEDNESS. Automotive ring gear differential. Axle shafts on roller bearings. 强度:自动差速齿轮,滚子轴承上的刚性车轴。
- The transmission is then moved toward the rear until the main gear shaft clears the clutch disk. It can then be lowered to the floor. 然后,把变速器主传动轴的端部从离合器中抽出,可将其放到地面上。
- For the non-locating position, a cylindrical roller bearing unit. 在非定位端是一个圆柱滚子轴承装置。
- The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法,分析了人字齿轮轴发生劈裂的原因。
- Conic roller bearing is used for desirable bearing capacity. 园锥滚柱轴承,承载力大。
- The numerical result showed that the length of the extended end of gear shaft has an evidential effect upon speed of losing stability of the system. 数值结果表明,齿轮轴外伸端长度对轴承的负荷分配和系统的临界转速影响十分明显,而对系统的失稳转速则影响较小。
- Oil, grease and other lubricants in roller bearing use. 油、油脂及其他润滑剂在滚柱轴承中的使用。
- The remedial maintenance method for broken gear shaft of small or medium equpment is introduced.The usual using can be essured after repaired. 介绍了中小型设备齿轮轴折断的修复方法。通过装配焊接的方式修复,可保证该轴正常使用。
- worm shaft roller conical bearing 蜗杆锥棍轴承
- Connecting rod tip are fitted with roller bearings. 连杆大端装配者滚柱轴承。
- Abstract The failure of a gear shaft was analyzed by SEM analysis, macrograph, metallographical examination, mechanical test, chemical analysis and etc. 摘要 采用扫描电镜、低倍检验、金相检验、力学试验和化学分析等方法,分析了人字齿轮轴发生劈裂的原因。
- Worn clothing and feed roller bearings. 针布破损和给棉罗拉轴承坏。