您要查找的是不是：
- gas solid film 气固膜
- Adhesion of Dry Solid Film Lubricants, Method of Test for (05. 干式固体薄膜润滑剂的粘合性的试验方法(05。
- Firstly,the pressure distribution of gas solid flow along the circulating route is analyzed and experimentally studied. 分析气固两相流在循环路径中的压力分布，并通过试验对其进行了研究。
- Measuring the Wear Life of Bonded Solid Film Lubricants in Oscillating Motion, Test Method for (05. 振动中粘性固体薄膜润滑剂的耐磨损的测量方法(05。
- Thermal Shock Sensitivity of Dry Solid Film Lubricants, Methods of Test for (05. 干式固体薄膜润滑剂的热冲击敏感性的试验方法(05。
- Pentachlorobenzene cyanide was synthesized by means of gas solid catalysis and chlorination using cyanobenzene and chlorine as the raw materials. 以苯甲腈和氯气为原料，用气固催化氯化法研制了五氯苯甲腈。
- Not only were there the gas solid two phase turbulent flows, but also there were heat transfer and cracking reaction in the commercial flow catalytic cracking(FCC) riser reactors. 工业催化裂化提升管反应器内既存在着气固两相的湍流流动，又存在着传热和裂化反应，而且这些过程是相互影响、高度耦合在一起的。
- The UV-induced trans/ cis photoisomerization and the thermal back-isomeriZation were investigated for the azo monomer and copolymer in solution and copolymer in solid film and correlated with the structures of the compounds. 研究了含对甲氧基苯氧羰基偶氮苯基团的甲基丙烯酸酯单体及其与含对甲氧基苯氧羰基苯基团的甲基丙烯酸酯单体的共聚物的氯仿溶液、甲基甲酰胺溶液和共聚物薄膜在紫外光诱导下的光异构化及热回复异构化行为。
- In order to ensure that the film will be in a solid film in quality,the determination of drying time is very important in inspect of the mechanical and physical performance of the paints. 涂膜的干燥往往需要一定的时间,才能保证最终形成固体涂膜的质量,因而干燥时间的测定是涂料常规性物理检验的一个重要方面。
- H heptafluoropropane (F 227) was prepared from hexafluoropropene (HFP) and HF by a continuous hydrofluorinating reaction in a gas solid phase system, and the technology was systematically studied. 以六氟丙烯为原料,经连续气固相氢氟化反应制备了七氟丙烷,并对工艺参数进行了系统的研究。
- The properties and components of pressure fluctuation signals in gas solid fluidized bed was dissected quantitatively by using power spectrum analysis,R/S analysis and chaos analysis. 应用功率谱分析、R/S分析、混沌分析等对气固流化床压力波动信号的性质、组成进行了定量解剖。
- The influence of the arrangements of pipes on gas solid flow characteristics in the dense section of standpipe in the circulating fluidized bed is studied on a cold state experiment platform. 在冷态试验台上研究了循环流化床料腿密相段中不同管束布置方式对气固流动特性的影响。
- WT5”BZ]The experimental study of a gas solid flow pattern and gas diffusion characteristics using polystyol particles and glass bead has been carried out in a pressurized spouted fluidized bed. 在一个加压喷动流化床装置上进行了冷态实验,研究加压条件下床中的气固流动状态和气体在各部分的扩散特性。
- The (Pb0.9-xLa0.1Cax)Ti0.975O3(PLCT100x) thin solid films were prepared by Sol-Gel technique. 采用Sol-Gel法制备了(Pb_0.;9-xLa_0
- W. Keppner, R. Wesche, T. Klas, J. Voigt, and G. Schatz, Thin Solid Films 143, (1986) 201. 黄隆玮，"银厚膜表面蒸镀铟、锡后之固液扩散接合研究"，中央大学机械所硕士论文，指导教授：林景崎(1999)。
- A. Piotrowska, E. Kaminska, A. Barcz, and J. Adamczewska, Thin Solid Films, Electronic and Optics, 130, 231 (1985). 李正中，“薄膜光学与镀膜技术”，艺轩图书出版社(1999)。
- Matter can exist as a solid, liquid, or gas. 物体存在的形态有固体，液体，气体。
- M. Menning, P. W. Oliveira and H. Schmidt, Thin Solid Films, 351, 99-102 (1999). 剧金兰,张鑫,赵石林,全国第二届奈米材料和技术应用论文集,5,43(2001)。
- M. Menning, P. W. Oliveira, A. Frantzen and H. Schmidt, Thin Solid Films, 351, 225-229 (1999). 罗吉宗,薄膜科技与应用,全华科技图书股份有限公司,(2004)。
