您要查找的是不是：
- Disconnect all fuel injection harness connections. 断开所有的燃油喷射电线束接头。
- WUXI EUROPE ASIA DIESEL FUEL INJECTION CO., LTD. 无锡欧亚柴油喷射有限公司。
- Jiangsu Sihong Fuel Injection Equipment Co., Ltd. 江苏泗洪油嘴油泵有限公司。
- ROAD VEHICLES. BASE MOUNTED IN-LINE FUEL INJECTION PUMPS. 道路车辆。平面底座直线固定喷油泵。
- A new method of fuel injection was developed during the war. 一种新的注油方法在战争期间发展起来。
- Woodward has a full range of fuel injection nozzles. 伍德沃德有一系列完整的燃油喷射喷嘴。
- The variation of nitrogen content in molten steel ha s been studied by Argon\|powder injection apparatus with sealing cover. 通过对密封罩吹氩喷粉设备工艺的设计应用，研究了喷粉脱硫过程中钢液氮含量变化。
- ROAD VEHICLES. END-MOUNTING FLANGES FOR FUEL INJECTION PUMPS. DIMENSIONS. 道路车辆。喷油泵用安装法兰。尺寸。
- Fuel delivery system can be divided into two categories, carburetor and fuel injection. 燃料供给系统可分为化油器和燃料喷射二大类。
- The method can realize nondestructive testing for fuel injection law without disassemble. 该方法可实现对喷油规律的不解体检测。
- Allowing a high compression ratio, direct fuel injection ensures maximum output of 327 kW (445 PS). 支持较高的压缩比，直接燃油喷射确保最大功率输出高达327 kw (445 PS)。
- The rear rack is square framework above which injector apparatus, cylinder, proportional pressure meter, oil cooler, electric engine and oil pump, etc, are equipped. 后机架为长方形框架,其上安装有注射装置、油箱、比例压力、流量油路块、油冷却器、电机和油泵等。
- Diesel engines - Cradle-mounted in-line fuel injection pumps - Mounting dimensions. 道路车辆。弧形底安装直列式喷油泵。安装尺寸。
- The emergency door which covers injector apparatus, blowing apparatus, turn device and shedder is installed above the front rack equipped with electric gas safety device. 在前机架的上面装有安全门，将注、吹合模装置、回转装置、脱模装置等罩在里面，且配以电气保险装置。安全门打开时，电气行程开关断路，机器不能工作，从而避免操作者的人身事故。
- The Practice of Real-time Monitoring &Simulating Teaching System on Automobile Fuel Injection based on MCGS Software and Data Collecting Card. 摘要：利用MCGS组态软件和数据采集卡对汽车燃油喷射系统的运行状态进行实时监控，功能仿真，具有直观、方便、节省开支的优点，在汽车教学中收到较好效果。
- Piezo Actuators are key components of piezoelectric fuel injection systems in diesel and gasoline engines. 压电致动器是在柴油和汽油发动机中压电燃料注入系统的重要元件。
- Hypodermic injection apparatus or accessories 注射仪器或附件
- These sensors establish ignition and fuel injection timing, and monitor crankshaft speed variation. 这些传感器（的信号）来对点火、燃油喷射定时和曲轴速度变化监控。
- Opening Pressure of Fuel Injector: 15,000–15,8kPa (2175–2291 psi). 燃油喷射器打开压力： 15;000–15;8kPa (2175–2291 psi).
- Above it, injector apparatus, blowing apparatus, turn device, shedder, emergency door, gas path system, mold temperature controlling distributor, water and electricity divider, etc. 其上安装有注射、吹塑二个合模装置，转位装置、脱模装置和安全门、气路系统、模温控制分配器、水、电分配器等部件。
