您要查找的是不是:
- It has locknut fasten rotor to a spindle. 配有防松螺母固定转子与中心轴。
- Position locknut over top of fuel pump module. 将锁定螺帽放在燃油泵模组上。
- Thank you,Freewheel ,for your enjoyable writings! 后生可畏;后生可贺!
- Tighten locknut 1 to fix the thread stand. 拧紧固定螺母1不让线架装置松动。
- Level3: Tolerance matching of freewheel bushings. Factory only. 级别3:飞轮轴套的公差矫正。只有工厂可以操作。
- SunTour's 1980 New Winner freewheel offered complete flexibility. 山图的1980年新的优胜者飞轮提供全面的灵活性。
- Recheck clearance on all valves again after locknut is tightened. 防松螺母拧紧后,再对所有气门的间隙重新检查一次。
- CKZ series freewheel is shielded by shield bearings on both ends. CKZ型为内含两套轴承支撑的楔块式超越离合器。
- Secure with locknut and gaskets. Install valve assembly. 用放松螺母和垫圈紧固。安装阀门总成。
- Type CK-B is a sprag type freewheel non-bearing supported.Nominal dia. CK-B系列为无轴承支撑外环两端面带键槽的楔块式单向离合器。
- Tighten left axle-end, insert freewheel (without pawls), tighten right axleend. 锁紧左侧的轴端盖子,插入花鼓本体(没有棘爪),锁紧右侧的轴端盖子。
- The valve is mainly made up of handle, body, disc, locknut and seal etc. 手动密闭闸阀主要由把手、阀体、插板、锁紧螺钉、密封装置等部件组成。
- Run sway the drift charging vehicle video frequency for my freewheel! 给我一个飞轮跑跑摇控车的漂移视频!
- To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/杆模块,先关闭供应管道,松开锁紧螺母,退出调节螺丝。
- To replace seat/stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/阀杆模块,先关闭供应管道,松开锁紧螺母,退出调节螺丝。
- Type GC-D is a roller type freewheel non-bearing supported, Earrings are required to support axial and radial loads. GC-D系列为无轴承支撑滚柱式单向离合器。
- Output flange is connected with output shaft by a involute spline, and fastened by a locknut. 输出突缘通过渐开线花键与输出轴相连,并用锁紧螺母将其锁住。
- SunTour also made a combined freewheel plus rear hub, called Unit-Hub, in 1969 for small wheel bicycles. 山图也发了联合飞轮加上后轮,称为股枢纽于1969年,小轮自行车。
- Use an open-end wrench and open the locknut on the accumulator valve assembly two or threefull turns. 使用开口扳手,打开蓄能器阀门上的防松螺栓-----------。
- This was the beginning of the Japanese derailleur and multi-sprocket freewheel industry. 这是日本变速器和多开始,链轮,飞轮产业。