您要查找的是不是:
- flow channel design 流道设计
- The Transaction Flow channel governs transacted message patterns. 事务流通道控制已经过事务处理的消息模式。
- A new oil-water hydrocyclone with spiral flow channel is presented. 提出一种螺旋形流道的新型油水分离装置。
- It has advantages such as reasonable flow channel structure; low pressure drop; high processing ability, high mass transfer efficiency, good design flexibility and wide applicability. 它的特点是流道结构合理,阻力降小,处理能力大,传质效率高,设计弹性大,适用范围广。
- Special channel design, multi-layer composite can minish transfiguration quantity effectively. 特殊流道设计,多层复合时能有效的减小各层分界面变形量。
- Sankey diagrams clearly depict the proportional amount a flow channel adds to a whole system. 桑基图清晰地描绘了每个添加到系统的流程通道的量。
- Standard clothes-rack channel design, sdjustable upper die lip, down die lip can be changed with vertical restrictor bar control. 标准衣架式流道设计,上模唇可调、下模唇可换及垂直节流棒调节装置。
- Adapting submodel technique, the paper specially discussed the cracking of concrete at top and bottom of flow channel. 采用子模型技术,详细考察了孔口流道顶、底板混凝土在自重情况下的开裂情况以及钢筋对混凝土的阻裂效果。
- Full equality for the medium of the body c**ity to provide a little resistance, through the flow channel. 完全平等的阀体内腔为介质提供了阻力很小、直通的流道。
- The uniformity of the non-block flow channel was so poor that the block in the proper position of the die channel was necessary. 模拟了两端进料式圆柱管无阻尼流道的流动均匀性后得到结论:两端进料式无阻尼结构的流动均匀性较差,宽机头中仍然有必要设置阻尼块;
- The FEM simulation of velocity distribution, viscosity distribution and pressure distribution of basket die flow channel was presented. 用有限元法对塑料熔体在筛孔板型机头的筛孔流道内熔体流动进行模拟分析,直观地展示了速度分布,粘度分布,压力分布,以及相关的数值变化。
- Also, the chamfer of the stay vanes entrance and the surface roughness of the flow channel were optimized by the numerical investigations. 亦对固定导叶入口冲角、涡壳壁面粗糙度对流动的影响进行了定量分析。
- In this article a method of CAD for centrifugal pump impeller is given and the sleek impeller flow channel with continuous curvature is gained. 提出了一种离心泵叶轮的计算机辅助设计方法,给出了保证叶轮流道光顺的几何模型;
- The design variables were assorted into two sets: the meridional channel design variables and the blade design variables that were treated as main system and subsystem, respectively. 该方法将设计变量分为叶片的设计变量和子午流道的设计变量,并分别作为子系统和中心系统。
- The primary step includes discharging mode design, signal design and channelization design of signalized intersection. 主要包括信号交叉口放行方法设计、渠化设计和信号优化设计。
- Next, taking manufacture of micro flow channel for example, the microfabrication and process flow are explained clearly. 接着以微管道芯片的制作为例,对微细加工工艺和流程进行了详细的阐述。
- The heat transfer and pressure drop of the entire flow channel of primary surface recuperator (PSR) were studied using 3-D numerical simulation. 对波纹状微型燃机一次表面回热器(PSR)全程通道的换热特性和压力损失进行了三维数值模拟分析,并与采用经验公式的计算结果进行了比较。
- The paper analyzed the tracking results from the eyeballing method on the video data, and found the method for applying it into the channeling design. 对目测法得到的交叉口车辆行驶轨迹结果进行分析,得出了车辆行驶轨迹应用于渠化设计的方法。
- On the basis of above work, I start the HAWP solution’s flow characteristics research in contracted flow channel porous model. 在上述工作的基础上,本文进行了疏水缔合聚合物溶液在收缩流道孔喉模型中的渗流特性研究。
- Then in the part of channelization design, it introduces the main affect and special adaption in the design of channelization traffic, especially the way of channelization. 在渠化设计部分,着重对目前的多种交叉口渠化方法进行了介绍,并分析了不同渠化方法的作用、适应性和特点。