您要查找的是不是：
- The tight line pumping at ordinary temperature method and SCADA-system have been adopted in Korla-Shanshan oil pipeline. 库尔勒至鄯善输油管道采用了常温密闭输送工艺及SCADA系统等先进技术,是目前国内自动化水平领先的一条管道。
- The components of a vehicle are encapsu-lated in their control components. With event, method, prop-erty and signal flow line, the transferring relationship betweensignals is established. 将车辆系统的各组成部件分别封装在各定制控件中，通过它们的事件、方法、属性和象征信号流向的线控件建立它们之间的变量传递关系。
- Currently the biosensor is a 25-millimeter-square plastic chip that has a meandering flow line running through it. 目前，这种生物探测仪是一个大小为25平方毫米的塑料芯片，有一个弯曲的流水线从中穿过。
- A flowchart symbol that represents a break in a flow line and that indicates where the flow line is continued. 表示流线断开的一种流程图的符号,并且说明断开的流线在何处继续下去。
- Now that you have mastered the basal body temperature method, some want to know the knowledge about menstruation bar. 现在你已经掌握了基础体温法，一定想了解一些关于月经的知识吧。
- Figure 1: Continuous flow lines in highly stressed crotch area. 图1：高应力弯钩区域的连续流径线。
- The flow line simulator has been used widely in the infill drilling and adjustment research. 流线模拟器已广泛应用于油田规模的加密钻井和调整研究。
- Objective To study the degradation kinetics of bulleyaconitine A (BLA).Methods Classical constant temperature method and HPLC were used. 目的 研究草乌甲素的降解动力学，考察影响草乌甲素降解的因素。
- In general, mold surface temperature lower than 82 C (180 F) may produce a hazy surface or a surface with flow lines, pits and other include defects. 大体上，形成表面的温度比82个C(180F)低可能用流程线生产一个朦胧的表面或者一个表面,坑和其他包括缺点。
- The solubility curves of OSO in both solvents were measured.The crystal growth experiments of OSO were made by the falling temperature method. 测定了OSO在苯和甲苯中的溶解度曲线,并用溶液降温法进行了晶体生长的实验。
- There are excellent production equipments in our company including full set of total package flow line and injection moulding machine. 公司设备精良,拥有全套的总装流水线和注塑机器。
- With the development of automatized and flow line welding production,high requirement on quality control and management has been put forward. 焊接生产规模不断向自动化和流水线方式发展,对生产管理水平提出了更高的要求。
- In the numerical model, the direct restraint method and the Coulomb friction method are introduced. A simulated temperature method is used to realize pre-tighten force. 在模型建立中,接触面采用直接约束模型,摩擦力的模拟选用库仑摩擦模型,在施加预紧力时,采用了虚拟温度方法。
- The article describes several methods of measuring on line temperature on the furnace and steel stock by means of data recorder with heat resistant,and discusses the methods applied widely. 介绍了运用耐热温度数据记录仪对炉温、钢坯进行在线温度测定的方法和一些新措施,并阐述了这一测定手段的意义。
- Based on the research of former, a general integrating lot sizing and scheduling problem(GLSP) for a capacitated flexible flow line is formulated. 在总结前人研究的基础上，建立了多级多资源的柔性生产线的分批与调度 集成模型（ GLSP）。
- The results showed that using the elevated temperature method the cell density first increased and then decreased with increasing foaming temperature, due to cell coalescence. 研究结果表明：对于升温法，随发泡温度升高，泡孔密度先增大后减小，这是高温下泡孔破裂合并的结果；
- Combining application of the point temperature method and thermal infrared imager can realize higher precision in the temperature measurement and deserves to be recommended. 点温法与红外热像仪结合，可以有效地提高红外热像仪的测温精度，值得广泛推广。
- Seam runs must be checked for flowing lines. 必须检查线缝,确保线条流畅。
- Advanced production technology of environmental protection is applied by the enterprise and the first "green" production flow line is established in Tangshan. 企业采用先进的环保生产工艺，在唐山建成了第一条“绿色环保”生产流线。
- Through flow line distribution and fiber contexture of inner material point obtained from no-flash die forging test, the forged gears with high quality grade was explained. 通过铅试件网格试验，揭示出在闭塞模锻中金属内部质点的流动规律、金属流线分布趋势及纤维状况，说明了锻造齿轮内在质量高的原因；
