您要查找的是不是:
- flow line pressure 流送管内的压力
- Seat tightness achieved with torque as opposed to line pressure. 利用扭矩而不是管路压力来实现阀座的密封。
- When this occurs, the valve disc moves to the closed position aided by the resetting shaft spring and line pressure, cutting the gas flow. 如此一来,阀门封盘藉由复归轴上的弹簧与管内压力,移到关闭位置而切断瓦斯气流。
- Line pressure tends to relieve gasket loads during operation. 在操作期间,管道压力倾向于释放垫圈负载。
- Currently the biosensor is a 25-millimeter-square plastic chip that has a meandering flow line running through it. 目前,这种生物探测仪是一个大小为25平方毫米的塑料芯片,有一个弯曲的流水线从中穿过。
- The distinction is that they operate under full line pressure and the redial flow within the unit can be either centrifugal (outward), centripetal (inward) or a combination depending on design. 区别在于它可以在全压力下进行操作形成离心(向外)、向心(向内)或综合式的放射状浆流。
- Figure 1: Continuous flow lines in highly stressed crotch area. 图1:高应力弯钩区域的连续流径线。
- Controlled closing of the valve, opens the mainline check valve, gradually increasing line pressure. 阀门受到控制的关闭操作,开启主管线止回阀,逐渐增加管线压力。
- A flowchart symbol that represents a break in a flow line and that indicates where the flow line is continued. 表示流线断开的一种流程图的符号,并且说明断开的流线在何处继续下去。
- The flow line simulator has been used widely in the infill drilling and adjustment research. 流线模拟器已广泛应用于油田规模的加密钻井和调整研究。
- Remove the throttle cable, cruise control cable (if equipped) and the transmission line pressure cable. 将节流阀电缆、车速控制电缆(若已配备)、及变速箱管线压力电缆拆下。
- Check initial pressure to see if full intended line pressure is applied at the valve inlet. 检查初始压力,看看是否全部预设管道压力是否应用在阀门进口处。
- There are excellent production equipments in our company including full set of total package flow line and injection moulding machine. 公司设备精良,拥有全套的总装流水线和注塑机器。
- Advantages: no pressure line of paper, cardboard single-trimming, single line pressure, the cardboard will deflect! 好处:不压线分纸、纸板单修边、单压线,纸板都不会歪斜!
- Seam runs must be checked for flowing lines. 必须检查线缝,确保线条流畅。
- Conversely, by opening the bleed, line pressure will blow out any accumulation when the plug is lifted. 反过来,通过开启排气装置,当阀塞升起时,管路压力将吹出任何累积物。
- With the development of automatized and flow line welding production,high requirement on quality control and management has been put forward. 焊接生产规模不断向自动化和流水线方式发展,对生产管理水平提出了更高的要求。
- Open test cock No.1 and No. 3 admitting line pressure to downstream side of second check valve. 开启测试旋塞1号和3号,是管道压力传到第二止回阀的下游一侧。
- Based on the research of former, a general integrating lot sizing and scheduling problem(GLSP) for a capacitated flexible flow line is formulated. 在总结前人研究的基础上,建立了多级多资源的柔性生产线的分批与调度 集成模型( GLSP)。
- Release the paint line pressure and switch off the power before doing maintenance with the sprayer or changing accessories. 在保养喷漆枪或者更换配件之前,松开喷枪压力阀并且关闭电源。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries