您要查找的是不是:
- float plate assembly 浮动板部件
- Measurement of clutch driven plate assembly thickness and parallelism. 从动盘总成厚度和平行度的检测。
- Tilt the head and mounting plate assembly until the desired position is found. 倾斜云台和安装板装置,直到找到所需位置。
- Sufficient stroke for floating plate? 浮动板是否有足够的行程?
- This equipment is for general assembly of clutch pressure plate assembly and calibration of diaphragm finger. 本设备用于汽车离合器压盘总成的总装和膜片分离指的校正;
- This equipment is for general assembly of clutch pressure plate assembly and callbration of diaphragm finger. 本设备用于汽车离合器压盘总成的总装和膜片分离指的校正;
- Decorating industry, plywood, strip plate assembly, furniture assembly of wood together with vines and so on. 装潢业的三合板、条板装嵌,家具制造业的木合装嵌藤具等。
- The stamping technique and design of bending former for a typical waveform piece in clutch driven plate assembly were introduced. 介绍离合器从动盘总成中的一种典型波形片零件的冲压工艺及弯曲成形模设计。
- The ejector plate assembly (shown dotted) naturally must incorporate holes bored in positions corresponding to those of the support pillars. 顶料板组合(如点划线所示)自然必须在对应这些支撑柱的位置上加工出一些孔。
- This distance can be minimized, however, by sinking the sprue bush deep into the mould plate assembly as illustrated, though Ibis necessitates using a special extension nozzle. 当然,这个距离可以用沉入模板组合的主流道衬套来尽可能地缩短,如图所示,但是,必须使用一个特殊的延伸式喷嘴。
- The energy method was applied to analyze the restraining action exerted by adjacent plate element in the same section,which is called plate assembly effect(PAE) in the stage of postbuckling. 本文根据势能驻值原理,建立了均匀受压矩形管的大挠度弹性屈曲理论,用于分析屈曲后相邻板件间的相互约束作用,即屈曲后板组效应。
- Water Head Loss of Float Plate Door and the Dash Force 浮板式拍门的水头损失和撞击力分析
- There wasn't enough water to float the ship. 水不够深,船浮不起来。
- Diaphragm spring pressure plate assemblies are widely used in most modern cars . 膜片弹簧压盘组件广泛应用于在现代车辆上。
- The divers tried to float the sunken ship. 潜水员想使沈船浮起。
- They decided to float a new company. 他们决定筹资创办一家新公司。
- The frame of floating plate which has good strength and stability is constituted by some equilateral triangle unit ,and the girder of the structure of floating plate extends to the edge of the frame. 浮盘骨架由若干正三角形单元构成,结构梁延伸至骨架边缘,骨架强度大、稳定性好;
- Form ties Bolt bore: bore drilling should be done when first time used form plate assembling on site to keep away from steel bar and reduce blank out bore happened. 7对拉螺栓孔:第一次使用的模板应在现场组装就位时钻孔,以避开钢筋,减少废孔的出现。
- Based on its characteristics,mechanical mobility and structural dynamics,some analytical formulae for three different plate assemblies with BBD are derived. 本文基于它的作用机理和机械导纳与弹性结构动力学理论,推导了三种不同BBD板结构振动功率流的解析表达式。
- He only put a bit on his plate to make fashion. 他只是拨了一点食物到盘子里做做样子。