您要查找的是不是:
- Note: 1.Size-Nominal diameter of the valve; D1-Diameter of the flange bolt hole center circle; D-Diameter of the flange bolt holes. 注:1.;规格尺寸为阀门通径尺寸;D1为阀门法兰孔中心分布圆尺寸;D为法兰孔直径。
- Lug body available with ISO flange dimensions and metric bolt hole threads. 凸耳式阀体符合ISO法兰尺寸和公制螺栓孔螺纹。
- Leak through diaphragm or around flange bolt holes of relief valve 隔膜或环绕安全阀法兰螺栓孔泄漏
- Limited distance deviation of the optional bolt hole on flange shall be 2mm. 法兰上非强制螺栓孔的有限距离偏差应该为2毫米。
- flange bolt hole 法兰螺栓孔
- Lug body available with ISO flange dimensions and metric bolt hole threads. For dead-end service use lug style (rated 200 PSI for this service). 凸耳阀体也可配置ISO法兰尺寸和公制螺栓孔螺纹。用于终端位置可采用凸耳结构(此时额定压力为200PSI)。
- Bolt hole fitting plastic core industrial caster. 孔顶塑芯工业脚轮。
- Stainless steel, aluminum. Under the operating condition of deep cooling, the materials of ring and flange bolt are the same. 不锈钢、铝。深冷工况下,环与法兰螺栓同材料。
- The bolt holes are in the unit base. 螺栓孔在单元的基部。
- All nozzle flange and girth flange bolts shall be of stud bolt type. 所有设备口法兰及翼缘法兰螺栓应为双头螺栓。
- Body and cover form up the workroom of impeller. On inlet and outlet flange there are bolt holes to mount vacuum gauge and pressure gauge. 泵体与泵盖构成叶轮的工作室。在进出水法兰上,制有安装真空表和压力表的管螺孔。进出水法兰的下部,制有放水的管螺孔。
- There is standard bolt hole connecting with the valve or bracket.The output axis in the middle is a standard internal octagon. 壳体上有标准的螺孔与阀门或支架相连。中间输出轴为一个标准的内八角。
- Looking for a bolt hole for you and your loved one this Valentine's Day? This selection of romantic retreats should inspire you. 充满充满波西米亚风情的广场酒店,一定会让你流连忘返。不过,要注意你的口袋哦,每天145英镑的花费,应该不算少。
- Do not rely on the flange bolting to support the valve or connecting pipeline. 不能依赖法兰螺栓来支撑阀门或连接管道。
- Position flywheel and O-ring on crankshaft and align bolt holes. 安装飞轮和O形环在曲轴上并对齐螺栓孔。
- Anchor/support bolt holes are located in base of body. 固定器/支架螺栓孔位于阀门的基座。
- Our most competitive products contains Hex bolt, Hex stock set bolt, Hex flang bolt, Carriage bolt, T bolt, U bolt, Machine screw, Auto screw, Threaded rod, and non-standard fasteners. 六角头螺栓,内六角紧定螺丝,六角头法兰面螺栓,马车螺栓,T型栓,U型栓,汽车螺丝,牙条和特种非标准件等。
- We are manufacturing mainly in: Fasteners: Hex Bolts, Hex Nuts,Flange bolt and Nuts,Carriage Bol... 供应标准及非标准螺栓,螺母,紧固件(图)
- Centerline of the slot at base of distributor is aligned to centerline of distributor holddown bolt hole on enginIn this position, the holddown bolt should easily pass through slot and into engine. 在分电盘基座上槽的中心线应与引擎上分电盘垂下螺栓孔的中心线对准。在这个位置,垂下螺栓应容易地通过槽进入引擎。
- Flange bolts may be tightened by conventional ring spanners on class 150# for utility piping systems. 150号等级的公用管道系统上的法兰螺栓可以使用通用梅花双头板手来紧固。